Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
Corner Cabinet Help for Lazy SusanI have a hang up. Hopefully someone can help me out. I have built quite a few cabinets for folks, but I must admit that i always end up b… Started by justin waldron in General Woodworking |
19 |
Jun 21, 2012 Reply by Paula Geihs |
Coarse vs Fine Thread ScrewsI am new to using the Kreg joining system and I see that screws are offered in both coarse and fine thread. Is there a "rule of thumb" to u… Started by Daryl Morse in Beginners' Zone |
12 |
Jun 19, 2012 Reply by Martin Rosendahl |
The new Kreg Jig..what time will it be announced Monday?Just wondering if I need to set the alarm extra early, ride the refresh button all day, or if there is a specific time the new jig is being… Started by Jason Watkins in Kreg Jig® Purchasing |
11 |
Jun 19, 2012 Reply by KregRep |
Kreg Pockethole PlugsHello, When I was building my bench, I was going to plug the holes. So I bought the Kreg plugs, well when I tried one it slid too far in.… Started by Jim Shelton in Other Kreg® Products |
3 |
Jun 19, 2012 Reply by Rick |
hellohello, my name is Hervin, I live in mexico city. buy the Kreg Jig Jr. and I'm ready to get started to work with, I find it an excellent too… Started by hervin in Community-Specific |
1 |
Jun 19, 2012 Reply by rick cruz |
doos and don't of the mighty jigOKreg! I use to do pocket holes by measuring carefully and then back-drilling from the end in the stock at about 5 to 10 degrees. Of course… Started by Pierre Vallee in Kreg Jig® Operation |
7 |
Jun 18, 2012 Reply by Ken Darga |
setting the depth collar for 1-1/2 thick material.I have the Jr. model. Setting the depth collar for 3/4 inch thick material easy and clearly marked, as is 1/2, 5/8, 7/8 and 1inch. I d… Started by jay a martineau in Beginners' Zone |
19 |
Jun 18, 2012 Reply by Ken Darga |
Source for fine hardwoodsHello Everyone, I'm pretty new to this wood working stuff and am becoming frustrated with searching for sources of nice hard wood to work… Started by Jake Frame in General Woodworking |
11 |
Jun 18, 2012 Reply by Jack Hockett |
Kreg Toolboxx replacement handle?I bought a Toolboxx for my dad for Christmas (and got one for myself while I was at it) and sadly, by the time my dads' showed up, his hand… Started by Bret Wortman in Kreg Jig® Purchasing |
5 |
Jun 18, 2012 Reply by William L Bonfiglio |
Router Table Vs. Shaper (Jet Jws-CCS Review)Ok, the age old debate, Router Table or Shaper… The best answer? It’s up to the individual and everyone has their opinions, but I will thr… Started by justin waldron in Beginners' Zone |
3 |
Jun 18, 2012 Reply by justin waldron |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service