Kreg Owners' Community

I'm inquiring about the use of this jig before I buy it. I need to determine if 1/4 " gap is the minimum possible. The spacers included with the kit are 1/4 and 5/16. I'm assuming this relatively wide gap is necessitated to allow fastening of the inside (adjacent to installed board) edge. That gap is too large for my plans. is there a way to reduce the size of the gap to 1/8 or even 3/16? Thanks for your help.

Jack G.

 

Views: 4702

Reply to This

Replies to This Discussion

Thanks, Noah.  I have been thinking about using longer screws.  Do you happen to have any brand name and store were these can be bought?  Kreg only has the one size.  I'll try sourcing it here in Canada after the holiday weekend.

I thought about using the deck jig myself, and in fact came very close to purchasing one, but like you the 1/4" or greater gap is far too great to use with Pressure treated lumber.  I'm not sure how many decks you've built Gary, but I'm sure not many in Canada where it's best to but the boards tight and let the gap build as the boards dry out.  At the end of one season you have a consistent 1/4" gap... that's 1/4" Canadian, Gary

 

 

Gary I completly agree with Ken to butt the boards with treated, when you buy a treated 5/4 board it is saturated, and if not it is warped.  If you butt the boards together within 1 month you will have a 1/8 to 1/4 inch gap when it shrinks.  So space it 1/4 if you want a 1/2 inch gap, your water will escape well?

Gary roofner said:
Decks in the US have always been built this way there's a reason you leave 1/4 inch gap it to allow water to escape . utter nonsense to butt the boards.
I am use to 2 x stock never have used thiner stock. So you are correct. Only one deck in old days just screwed through and into the joists. Learn something new everday. You are aso right you ended up with a gap of about 3/8 to half inch no problem still strong. 

In the northern country, it may be common practice to start with a 1/4'' gap, between the deck boards.

After the boards dry, a 3/8 - 1/2" gap appears---

which would allow snow to fall thru the cracks, resulting in less snow to shovel from the top side.

 

 

So basically the common / majority concensus seems to be butt the boards - which by default means that the Kreg Deck Jig is not required unless using manufactured boards

George, I get three inch screws that work with the deck jig here, but I don't know if they ship to Canada:

http://tinyurl.com/3of2xgq

But any #7 trim head screw should work with the jig as long as the head is 1/4" or smaller. 

And to address the spacing issue, it is easy to slice or grind down the nubs on the back of the locating bar on the jig get spacing down to 1/8" if that is desired, although a deck board should always have at least 1/4 spacing so that debris does not get stuck. I have never used perforated, wet, pressure treated lumber for a deck. Here in WA there is a product called sunwood, amongst other names, which is treated, non-perforated and dry. I prefer to use 2x or 5/4 cedar, which is also dry. Putting down wet wood introduces too many variables, and especially when edge-screwed, can move and split when it dries.

George Godfrey said:

Thanks, Noah.  I have been thinking about using longer screws.  Do you happen to have any brand name and store were these can be bought?  Kreg only has the one size.  I'll try sourcing it here in Canada after the holiday weekend.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Miter Saw Recommendation

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone Jul 22.

Miter saw stand

     Has anyone used one of the Kreg Universal Stand configurations as the base for a miter saw workstation with fold down wings?  I scrolled through the pics in the community and all I saw were using a DIY base cabinet.  I have an extra Kreg router…Continue

Tags: saw, Miter

Started by Bill Murphy in Other Kreg® Products Jun 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 7 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_