Hello,
I'm new to this forum as well as woodworking and i'm looking for some advice in selecting a router to match up with the kreg precision router table.
If anyone has any suggestion for routers or lift kits that are compatible with this table and will make learning and using this router table easier they would be greatly appreciated.
I plan to use this router to build book cases and a toy box for my daughter. i would also like to build some shop[ cabinets as well for my first few projects.
Which router bits would you buy if you were starting out new?
Thank you in advance for any advice
Sincerely,
Bob Garrison
Tags:
Make sure you get a router that accepts both 1/4" & 1/2" shank bits. A 2HP or larger motor since it sounds like this tool will be a workhorse in your shop.
I started with the router bit sets with the basic roundovers, trim bits & a couple ogee bits & bought as needed from there.
Whiteside used to have a very nice starter kit.
Most of these kits are 1/4" shanks.
HTH
I just bought one of their tables as well and got a Triton to go with it as the triton has the built in lift. Works slick
thank you guys for your help. I will look into the triton routers
Triton all the way i have two.
an observation: i am jock i live in brisbane my bench router is hitachi 2hp i made a lifter out of an old car bottle jack and a wooden cradle to move the router up and down. it works for me being a low tech person an the fact that store bought ones are expensive (this is the scots coming out in me lol) the accuracy that it gives me is very good. router bits are very expensive in oz that is if you want good ones but there is a chinese company called "BANGGOOOD" that sells a large variety of bits at 1/4 of the price of the name brands and in some cases you don't pay for delivery from their wharehouse stores. they have these stores world wide. type banggood into search bar and have a look may save you a whole lot of money.
I agree with the posts about the Triton, mainly because of its HP and the built in lift. I have Porter Cables and the Kreg PRS lift which works great. Would definitely advise to have Kreg supply the pre-drilled plate for whichever router you use.
The PRS tables by Kreg are feature packed and well designed. I have found that the table top small unit is a great addition for shorter pieces and nice when you have two different cuts to make such as on cabinet rail and stile making. However, the top of the line PRS top and table are where you want to start because of the fence and top size. For bits, you can find a good selection and supporting videos at MLCS Router on the web.
I have been using routers for 50 years now and thought that I could make a good router table for a whole lot less. After a few usable and not so usable ones I bought the Kreg. It really raised my abilities to do quality work a whole lot safer than I had been able to do on my home-brew versions. I wish I hadn't waited so long..
Be sure to get good feather boards and push sticks
Thank you all again for your advice.
I have little confidence in my ability to build my own router table and lift, so I pulled the trigger and ordered the table with feather boards, micro adjuster, casters, setup bars and a pre drilled plate.
I also ordered the 3 1/4 hp triton router. I have heard a lot of good things about their routers, so when many of you suggested the same that made that decision very easy.
I can't wait to get this all set up and start learning.
Thanks again to you all for your advice.
Bob Garrison
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service