Kreg Owners' Community

Does anyone out there happen to own this model (R4512) table saw?  I got a great deal on one (new) from "Big Orange" and would like to discuss a few things about it.

 

Thanks in advance.

Views: 15905

Reply to This

Replies to This Discussion

Steven Akers  ..... 

I had no trouble at all with my lift assy.  I looked closely at the photos in the book and then set the parts on a table to best represent the photo.  I put them together and everything was just fine.  I opted to purchase a ZERO clearance insert for mine.  I'm sure I've mentioned the brand elsewhere in this thread. 

 

Rudy Timmerman  .....

Before messing with the trunnions etc. I would suggest you put on a "better blade" than comes in the box.  Mine appeared to heel slightly too until I replaced the blade.  It seems my blade was actually the problem.  I verified this using a digital meter on the arbor (with blade removed)  It measured .000.  With the original blade on it measured .007.  I replaced the blade with a Freud 80 tooth and the blade now measures .001.  That is surely a close enough tolerance to work with.  Good luck.

I had to make a very small adjustment to my trunion.  It was out by .002 and now <.001.  I started to suggest to Ridgid that they number the lift parts and reference them on their instructions but sounds like the new saw has better illustrations.   I buy a lot of Ridgid tools at their distribution center.  They have public sales about 4 times a year.  They make pretty good tools in my opinion.


Steve Gronsky said:

Steven Akers  ..... 

I had no trouble at all with my lift assy.  I looked closely at the photos in the book and then set the parts on a table to best represent the photo.  I put them together and everything was just fine.  I opted to purchase a ZERO clearance insert for mine.  I'm sure I've mentioned the brand elsewhere in this thread. 

 

Rudy Timmerman  .....

Before messing with the trunnions etc. I would suggest you put on a "better blade" than comes in the box.  Mine appeared to heel slightly too until I replaced the blade.  It seems my blade was actually the problem.  I verified this using a digital meter on the arbor (with blade removed)  It measured .000.  With the original blade on it measured .007.  I replaced the blade with a Freud 80 tooth and the blade now measures .001.  That is surely a close enough tolerance to work with.  Good luck.

 

Thanks for the advise.  I will do this for sure.  Anything from having to get on my hands and knees lol.  It is a bitch to get old.  

Hey Steve.  Left you a comment.  One World Technologies or TTI is located near Greenville, SC.  They own Ridgid along with Ryobi and Milwaukee. The are somehow involved in the purchase of Delta also.  The have a sale open to the public about 4 times per year.  They have both new and refurbished items for sale.  I picked up a new Ridgid compact jigsaw and an orbital sander on my last trip.  Most everything in my shop has come from there.  I can send you there last listing if you like.
Well, unfortunately the blade was NOT the problem on my new Ridgid 4512.  Tried to adjust the trunnions, but no luck moving them (would not even budge with a clamp).  The handbook just mentions 4 bolts to be loosened, but no luck.  Am I missing something?  Rudy
Hi Steve. I own a Ridgid R4510. Is that close enough?

Nothing that I'm aware of.  The 4 trunion bolts are supposed to be all there are.  I have seen that some folks "hit" it with a piece of wood, but I would be very careful with that.  Fortunately I didn't have to go through that stuff.

 

Steve


Rudy Timmerman said:

Well, unfortunately the blade was NOT the problem on my new Ridgid 4512.  Tried to adjust the trunnions, but no luck moving them (would not even budge with a clamp).  The handbook just mentions 4 bolts to be loosened, but no luck.  Am I missing something?  Rudy

For curiosity, is that the model with the ALL cast iron table (main table PLUS extensions)?  I am considering changing my metal extensions for Cast Iron, but I must do more research.  Ridgid "doesn't recommend altering the factory equipment".  That sounds kinda political, doesn't it?

 

Steve


Rick Starr said:

Hi Steve. I own a Ridgid R4510. Is that close enough?

Hi Steve:

I tried everything I could from tapping it to clamping pressure, but nothing budged.  I also changed the original blade to a Freud 80 tooth fine finishing blade, but that made no difference either.  Re-checked the bolts, and I can hand loosen or tighten them.  So, the trunnion SHOULD be movable.

Rudy 


Steve Gronsky said:

Nothing that I'm aware of.  The 4 trunion bolts are supposed to be all there are.  I have seen that some folks "hit" it with a piece of wood, but I would be very careful with that.  Fortunately I didn't have to go through that stuff.

 

Steve


Rudy Timmerman said:

Well, unfortunately the blade was NOT the problem on my new Ridgid 4512.  Tried to adjust the trunnions, but no luck moving them (would not even budge with a clamp).  The handbook just mentions 4 bolts to be loosened, but no luck.  Am I missing something?  Rudy

Not sure if you are asking me, but just in case.  The model I have does not have cast extensions.  Was planning to replace one of them with a Bench Dog router table, as I have a small shop in my basement where the Ridgid is set up.  In fact, I actually cut down the fence a bit, as I did not need to rip anything wide there.  I have another TS in a 12x12 shed outside where I cut the bigger sheets.  With the shed doors on both ends open, I have lots of room there to handle the bigger stuff.

Rudy 

Steve Gronsky said:

For curiosity, is that the model with the ALL cast iron table (main table PLUS extensions)?  I am considering changing my metal extensions for Cast Iron, but I must do more research.  Ridgid "doesn't recommend altering the factory equipment".  That sounds kinda political, doesn't it?

 

Steve


Rick Starr said:

Hi Steve. I own a Ridgid R4510. Is that close enough?

If it isn't moveable, I can only suggest you contact Ridgid / Home Depot tech support.  I don't know what to tell you beyond that.

 

Steve


Rudy Timmerman said:

Hi Steve:

I tried everything I could from tapping it to clamping pressure, but nothing budged.  I also changed the original blade to a Freud 80 tooth fine finishing blade, but that made no difference either.  Re-checked the bolts, and I can hand loosen or tighten them.  So, the trunnion SHOULD be movable.

Rudy 


Steve Gronsky said:

Nothing that I'm aware of.  The 4 trunion bolts are supposed to be all there are.  I have seen that some folks "hit" it with a piece of wood, but I would be very careful with that.  Fortunately I didn't have to go through that stuff.

 

Steve


Rudy Timmerman said:

Well, unfortunately the blade was NOT the problem on my new Ridgid 4512.  Tried to adjust the trunnions, but no luck moving them (would not even budge with a clamp).  The handbook just mentions 4 bolts to be loosened, but no luck.  Am I missing something?  Rudy

Came to the same conclusion, as I don't want to break anything.  Thanks for all the help just the same :)

Rudy

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_