Kreg Owners' Community

Just purchased a Kerg-Flex Featherboard for my Craftsman 10" table saw. It fits perfectly in the slot but it slides with the board being cut. How does one stop it from sliding freely. Apparently I missed something. Any suggestions?

Views: 1932

Reply to This

Replies to This Discussion

I have same featherboards with a craftsman jobsite saw and it works fine. I just tighten down knobs and it stays tight. I am not sure what the problem could be.

The Wedge Lock blocks should snug down in the slot as you tighten the knobs to hold the featherboard in place firmly. If you aren't able to tighten the knobs sufficiently, first make sure that the wedge locks are expanding as you tighten the knobs. If they are, you could try roughing up the edges of the blocks a bit with sandpaper. This really shouldn't be necessary, though.

If there's a problem with the wedge-lock blocks or if you can't make the featherboard work with this saw for some reason, contact our Customer Service Department online at: http://www.kregtool.com/Customer-Service-Serve.html or by calling 1-800-447-8638.

KregRep



KregRep said:

The Wedge Lock blocks should snug down in the slot as you tighten the knobs to hold the featherboard in place firmly. If you aren't able to tighten the knobs sufficiently, first make sure that the wedge locks are expanding as you tighten the knobs. If they are, you could try roughing up the edges of the blocks a bit with sandpaper. This really shouldn't be necessary, though.

If there's a problem with the wedge-lock blocks or if you can't make the featherboard work with this saw for some reason, contact our Customer Service Department online at: http://www.kregtool.com/Customer-Service-Serve.html or by calling 1-800-447-8638.

KregRep

Thank you for the suggestion. I applied more pressure to the knobs and the featherboard locked in place. I was afraid of applying to much pressure. The featherboard did not include any instructions so I didn't know what to do. I would like to add that I am very satisfied with your line of tools. Keep up the good work.

You could also place a piece of tape on one side of the blocks if a little loose.Have a good day.

I have had the opposite problem getting them to release. Which was a known problem.

Thanks to all of my Kreg friends. I have it now and I'm off and running.

Charles,

The fasterner only needs to be snugged-up, (finger tight), to keep the tool from slippage.

Over-tighening isn't necessary-- it only makes it more difficult to loosen. 

Adding masking tape to one vertical face of the slide-bar, as suggested, is a good idea---it may be necessary then the miter slot as been waxed.

PS---

If insufficient space does not allow the use of ''tape'', along the side of the bar,

clean the surface areas, (remove the wax, oils, sawdust, or the like), from the miter slot using a mineral spirits dampened cloth, allow to dry and re-insert the feather board bars/blocks into the miter slot.



Ken Darga said:

Charles,

The fasterner only needs to be snugged-up, (finger tight), to keep the tool from slippage.

Over-tighening isn't necessary-- it only makes it more difficult to loosen. 

Adding masking tape to one vertical face of the slide-bar, as suggested, is a good idea---it may be necessary then the miter slot as been waxed.

Gary, 

Place a metal ''flat'' washer under the end of the knob---

so the knob rotates on the surface of the washer.

Fender washers are handy---clamping pressures are distributed to a larger surface area. 

In some applications, a nylon washer is beneficial over a metal washer.

(When tightening the knob, the friction between the knob and the plastic surface of the feather board increases, and requires additional rotating force to loosen).

Generally, I've found that ''finger-tight'' was adequate. 

I prefer knobs with wing or T-style feature, to a round knurled type, for such clamping applications.


Gary roofner said:

I have had the opposite problem getting them to release. Which was a known problem.

I came across this post from 2013 in researching what sounded like the exact same problem. 

After reading the replies that explained that only "hand tightening" should be needed, I realized that the wedge locks wern't expanding at all.  I had assembled the featherboard with the wedge locks upside down!  It doesn't look wrong to the newbie, but the wedge locks don't expand and the whole assembly slides. 

Once I flipped the two wedge locks over, the featherboard works great.  Hand tightening the knobs does indeed secure the assembly in the miter slot.

Thought I'd share this for the next person.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

New to K5 and pocket holes, any video’s on the materials listed below?

I am using Danny Proulx book on shop workstations. I am deciding whether to use MDF or Melamine. He calls for MDF. However; I like the looks of the melamine.  I am a little leery of using pocket holes for it. One of the main reasons is I have no…Continue

Started by Michael Lusk in Beginners' Zone on Saturday.

Adaptive Cutting System T-Track Stops Mod 1 Reply

I bought the ACS a couple of weeks ago & have been pleased with the results on my first small project (LP record crates)... I was disappointed with the plastic accessories for the table-top, especially the T-Track stops. I'm pretty sure they…Continue

Started by John Moore in Beginners' Zone. Last reply by Deac Manross May 17.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_