Kreg Owners' Community

How do I adjust my old model 1703-1 Black & Decker chop saw?

My saw is several years old and seems to work fine, except it is off when I do a miter & they don't fit correctly. I am using a 45% angle, it is frustrating as I don't want to waste my wood. Does anyone have any suggestions about how to adjust it? The fence is solid and doesn't have any adjustment screws.

Views: 3513

Reply to This

Replies to This Discussion

first thing you would have to know is where are the adjustments for the saw position. your instructions that came with it should have that information. when you know where that adjustment is you can use a 90 degree and 45 degree angle tool to set the blade. use your fence with the 45 degree tool to adjust the position of the blade. lock down the adjustment bolt or screw and test. i hope this makes since.
Thanks Brent, only problem is this was an old one my Dad used to have, my brother gave it to me, but there were no directions. My father is no longer living either. I did hear that there might be an adjustment underneath, do you think that might be it?
I don't have that saw or the instruction manual, but I did some internet searching and came up with the attached diagram of your saw parts.  Somebody might be able to look at the diagram and give you some advice as to what to try to adjust your saw.  Sorry I can't be of more help.
Attachments:
try this site. it has video on how to adjust your miter saw. http://www.ereplacementparts.com/black-and-decker-miter-saw-parts-c...
Hmm, that's kinda strange. Usually if they are off at one setting they are off on all of 'em. Does it cut a dead bang 90?
Thanks everyone. To answer your questions, no the 90 degree is off about 1/8th of an inch, There are wood pieces across the fence, but they don't appear to be damaged.  I did have the diagram and did view the video, I wish I had all those adjustments! I am enclosing a picture of the bottom. All the screws/bolts that are showing seem to be permanent ones, not adjustable.
Hi Sherry - that large, black bar doesn't look square to me. Try loosening those two bolt and see if you can rotate the table a little. I'm guessing the bolt holes are slightly larger than the bolts to allow some adjustment there.

Sherry K. said:
Thanks everyone. To answer your questions, no the 90 degree is off about 1/8th of an inch, There are wood pieces across the fence, but they don't appear to be damaged.  I did have the diagram and did view the video, I wish I had all those adjustments! I am enclosing a picture of the bottom. All the screws/bolts that are showing seem to be permanent ones, not adjustable.
Thanks John, my brother in law and I tried this and it worked great, it was off about 1/16th of an inch, who could tell it made all that difference. Also there was a little pointer show the mark, it broke off when we took it apart. We decided to use a file and mark a notch on the metal left behind, I think this will pretty well. I appreciate everyone's help. Now what can I make next? Actually we worked on extending a kitchen island this weekend. Not quite done yet though.

I see how you adjust the miter, but how do you adjust the bevel?   Anyone found a manual? 

Are we talking about the same saw? Usually there is a lever on the back side to loosen the bevel set. A lot of the older ones are miter only, you got a bevel by rotating the stock 90°. How about a pic or two. Front and back would be helpful.
 
Paul Schuster said:

I see how you adjust the miter, but how do you adjust the bevel?   Anyone found a manual? 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_