Kreg Owners' Community

I've started building a cabinet with poplar.   I wish to have a black gloss finish.  I'm not an experienced "finisher".  I don't see much in way of stains in black at the common home stores.   I have also been told that attempting to stain poplar black really won't work out.   I see one of the nice projects on the site, a kitchen bar, was finished with a high gloss black paint.      Would you agree that for a basic black finish to stay with a paint vs stain?   Also,  it would seem that in order to avoid brush strokes it might work to use a couple/three cans of spray paint e.g. Krylon.    But somehow my guts says don't try that.   Are there any strong opinions of do's or don't here?  thanks for your thoughts.

Views: 462

Reply to This

Replies to This Discussion

I have tried a black stain for a small project. It worked Ok, but I wasn't looking for a high gloss on it.

I have sprayed a flat black (Mickey mouse band saw box) on pine using Rustoleum High Performance spray, and it worked better than I had anticipated, especially on pine with no seal coat below the paint.

Working with poplar I think I would sand to 320 grit. Raise the grain and lightly sand at 320 again. Use a good sealer (a couple of light coats of dewaxed shellac).  Scuff with scotch bright. Then lightly spray with your black paint. Use many light coats with a scuff between coats.

You could use an Ebony wood stain followed by a couple of coats of clear varnish. It would look mega.

Google "BLACK FRIARS", their wood stains are fantastic. 

You can use a beeswax instead of varnish too if you prefer.

Good luck.

Zinsser makes very good products

1. Sealer

2. Primer-sealer

nothing is better at permanently blocking stains and wood knots

Works with any top coat.

I use the primer-sealer on wood before applying the paint, 

so as to obtain a evenly finished top coat.

I sand using 220grit, before applying the primer-sealer.

Remove all sanding dust before applying the sealer.

Poplar is a porous material that is uneven in color.

Some areas of poplar is a greenish color.

Without a primer-sealer, you won't get an even finished color.

NOTE:  some black stains will not produce a evenly colored finished surface.


Thin the 1st coat of paint with a 25% cut.

I want the first layer coat to be a thin film.

NOTE:  If spray painting, use a spray booth.

A simple suitable size spray booth can be a wall(s) of cardboard; such as a cardboard box from a large appliance, plastic drop cloth, or the like.

Thank you Tim, Nick and Ken.   Your input has certainly pointed out gaps in my knowledge.   With your input I think I should be able to get this at least 'pretty good'.    I'll probably post the project in about a month  (would like to get it sooner,  but playing in the garage  unfortunately is not my main occupation).

You're welcome Bill. practice on some off cuts, you'll soon get it mate,

Good luck, we look forward to the pics.


RE "Black stain"---it's like a "dye-like" material---

it will not cover the imperfections and color variations in poplar wood.

The variations will be visible when a varnish like material is applied over the black stain.


is a paste-like material.

It's a waxy sticky substance.

I wouldn't use or recommend it, for your application.

The wax will attract and hold dust/dirt particles, 

and be difficult to maintain a clean-like surface.

Before using beeswax on your finished product,

make some sample test pieces, so as to see for yourself the problems you'll run into.

I recently had the same question regarding staining birch plywood a deep black color.

The research I did led me to try black leather dye. This dye in fact.

Worked wonderfully! The blackest black color I've ever used. Doesn't raise the grain. A little went a long way. Used a foam brush. Had no problem with overlap strokes showing up.

The pics are of an equatorial platform for a large telescope.


Try a General Stain it works very well. It is available through Lee Valley in Canada, not sure where you are.  

Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 


  • Add Videos
  • View All


Recent Workbench Survey Legitimacy

Yesterday, I received an email wanting my opinion on Kreg adding high end workbenches to their product line and wanted to know before I clicked the link if this is a legitimate survey or some phishing scam. Here's the link I was provided (…Continue

Started by JOHN W. GOETZ in Other Kreg® Products Dec 10, 2021.

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11, 2021.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…


Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…


Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service