Kreg Owners' Community

Hello my Kreg friends,

I have been off this forum for some time now, but I am back.

I have build a few children's 30" table and chairs - which I am very happy with the results.

But now I want to build a 60" round dining table - using the Kreg system for the top.

Instead of finding 1 1/2 inch wood, I thought I would use 1 inch (3/4") hardwood material for the top of the table and then construct another  58 inch round top to attach just below it for a nice look. After building each I thought I could attach these pieces Kreg end to Kreg end.

Any thoughts about this idea?

Will the Kreg system be good long-term using this procedure?

I look forward to your responses.

Thank you in advance for your thoughts.

Marty

Views: 183

Reply to This

Replies to This Discussion

Hi Marty. I don't understand the "kreg end to kreg end" part so I'll just say if you're just edge joining the boards with PH screws then the answer is yes it will work. However,, by gluing those edge joints AND using the PH screws as clamps then you'll have,, in my opinion,, a much stronger piece that will last a lot longer.

I think rotating the tops 90* to each other is a great idea to prevent cupping or warping. Then mount the legs in line with the 60" top.

Just a side thought. I would consider two 60" tops rather than the one 58" & 60". I would rout a 45* chamfer on the lower piece. This is just how I'd like MY top to look. Your idea will be very nice as well. 

Glen,

Thank you very much for your reply.

And yes, I had planned to use pocket holes and glue.

Once the two tops were completed I planned to rotate/attach them at 90 degrees as you also suggested.

My concern was warping/cupping. I think you answered my question. 

Glen, would you mind attaching a picture of one of your completed tables. I would love to see it. 

And thanks again for your response.

PS I had seen a picture of a beautiful round table in a magazine with the 60" round table top attached to a 58" table top - both tops routed round.

Hi Marty I made a 60'' round table using pocket hole joinery just go to my page and check out my pictures

Thank you Ray,

A couple of questions:

1) It looks like you doubled up on each pocket hole, correct?

2) What size of boards did you use for the table top?

3) Was it difficult to make the round edge band?

Thanks,

Marty

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-cut

Looking at buying the Kreg Accu-Cut and am interested in hearing feedback.Thanks.StanContinue

Started by Stanley C. Pearse in Beginners' Zone Jul 1.

Wheelbarrow organization 2 Replies

Anybody have any ideas on how to make a couple wooden attachments for the side of a wheelbarrow that can hold and secure some long handle yard tools?

Started by Vincent A Cutright in Beginners' Zone. Last reply by Vincent A Cutright Jul 6.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_