Kreg Owners' Community

Perhaps this question has already been asked somewhere on this forum but I wasnt able to find it after an hour or so of searching. Is there a recommended length of Kreg screw to use when combining a 1x6 into a 4x4 post. I have seen a few conversion charts and what not on the page but nothing goes up to a 4x4 post. 

Building a dinning room table and dont want anything coming out after I deliver it to a friend. 

Views: 1152

Reply to This

Replies to This Discussion

I assume that the pocket holes will be in the 1x6, and the sharp end of the screw will be entering the 4x4. If this is true, then you'll want to set the jig height and drill bit stop for the 1x6 thickness (0.75 inch).

Not sure where the 1x6 is along the 4x4. If the 1x6 is flush with the outside and the pocket holes are on the inside, you'll need to be careful with the screw length - otherwise it will exit out the side of the 4x4. The length should match the 0.75 width - as if you are attaching to another 1x material.

If the 1x6 is in the middle of the 4x4, then there is not much concern about the screw exiting the side. I think it could be quite long.

The best thing to do if possible is a test run with the materials using scraps.

I am actually screwing it into the middle and attempting to make it flush with the 4x4. I used your suggestion of trying it out on some scraps with various screw lengths and ended up using the 2 1/2 screws and it actually went just fine. I got it to be flush and very secure into the 4x4 with that length. The original 1 1/4 length screws just weren't really holding it as secure so this definitely works. 

Thank you for your help!

If you were using a 2x6 instead of the 1x6 I might suggest using the Kreg HD Jig with its bigger (stronger) screws. I'm a big fan of the HD Jig! 

The regular 2-1/2" Kreg screw is a #8 gauge (about 3/32" thick), but the HD screw is a #14 gauge (about 1/4" thick, and 2-1/2" long) - MUCH thicker and stronger. 

My 2 cents... I would not give up on a nice and thick layer of a wood glue in the joint... This with 2 1/2 " screws will make that joint stronger than the wood itself. 

Dave N said:

I am actually screwing it into the middle and attempting to make it flush with the 4x4. I used your suggestion of trying it out on some scraps with various screw lengths and ended up using the 2 1/2 screws and it actually went just fine. I got it to be flush and very secure into the 4x4 with that length. The original 1 1/4 length screws just weren't really holding it as secure so this definitely works. 

Thank you for your help!

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

Videos

  • Add Videos
  • View All

Forum

Back with Kreg 3 Replies

After being disappointed with my Kreg Foreman I sold it and got a Porter Cable 560. It was a decent jig and performed with decent results. Then a friend who is also a Kreg dealer told me about the K5.i bought one and set it up. I must say it's…Continue

Started by DaveTinley in Beginners' Zone. Last reply by KregCS on Wednesday.

spam 3 Replies

Did anybody get bs email from Timothy White about Your surname? He said he got my name from here.Continue

Started by Timothy Spoon in Beginners' Zone. Last reply by KregRep Apr 4.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_