Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
introductionHello my my name is Tom Comeau and I am from Barrington N.H. I have recently retired from the fire service and need to get back into carpen… Started by Tom Comeau |
3 |
Feb 14, 2011 Reply by steve kidd |
Scrap woodI have a cardborad barrel that I keep my scrap in instead of tossing it and going to lumber yard everytime I need a small piece of I seasrc… Started by Robert W. Goodfellow |
0 | Feb 10, 2011 |
Getting the spamActualy I'm not surprised. Some of you may have heard this before Something that is locked up, only keeps the honest man honest. A spammer… Started by Michael A Clark |
1 |
Feb 9, 2011 Reply by Michael Campbell |
Doing family projects.When doing a family project whose in charge, you or your mate? And do disagreements over the project create problems in the relationship? Started by Stephanie M. Williams |
3 |
Feb 7, 2011 Reply by James Waller |
Router Table AdviceI am in the market for a router table and looking for advice. I was leaning toward the Kreg Table top for both cost and space savings. On… Started by Mark Ruggles |
5 |
Feb 1, 2011 Reply by Ralph Sarc |
Beaded Fence Frame SystemWhat is the best drawer slided to uses with inset drawers and what is the best hinge for the doors. Started by Paul Jacobsen |
0 | Jan 23, 2011 |
drill bit quick releaseGetting my bit into my Kreg quick release was easy but now I can not figure out how to get my bit out of my Kreg quick release. What do I… Started by richard eugene sayre |
1 |
Jan 23, 2011 Reply by James Waller |
Magazine rackDoes anyone have any designs for a combo magazine rack/toilet paper holder for bathroom?? Started by Merwyn Bowdish |
4 |
Jan 20, 2011 Reply by Gary roofner |
90 degree joint from 2 x 45 degree mitres.I have just started using the pocket hole jig and can find plenty of online literature and advice on setting up for a 90 degree butt joint.… Started by Phil Roche |
1 |
Jan 16, 2011 Reply by tom welch |
Long Fine Thread Screws for joining thick hardwoodsI know it's a bit of an adventure, but I'm planning to build with cabinet where the hardwood frame is made from 1-5/16 (after planing) thic… Started by gdatomic |
2 |
Dec 15, 2010 Reply by gdatomic |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service