Kreg Owners' Community

Hi there,

I was wondering if I could use particle board or mdf to make tall cabinets (8 foot high, 4 feet wide, 2 feet deep) using pocket holes to assemble them.  And at the end attach a face frame on to it. Most cabinets here in Europe are made from particle board covered with melamine, sometimes MDF is used (to be painted). Almost never plywood is used, You can't get prefinished ply anyways. I am planning to build a couple build in cabinets in the basement, between 2 brick walls (about 4 feet seperated from eachother), and I thought about screwing spacer boards on the walls, then slide in the cabinets, screw them on the spacer boards and at the end put a face frame onto it with biscuit cookies.

The shelves would be made very sturdy, yellow poplar construction ( 1 inch thick, 2 inch heigh) with a top in mdf 1/2", and a bottom in mdf 1/2" also. Screwed into the sides of the cabinet.

Later on, when everything is finished I might put some doors onto it also.

Anyone experience with MDF, particleboard as a material for cabinet construction using pocket hole joinery.

thanks for the info.

Views: 13981

Reply to This

Replies to This Discussion

Miroslav, 

You can definitely use MDF and particleboard with pocket holes. However, you will want to be very careful when driving your screws. If the clutch is set too high, your screw will continue to drive and will come out the other side. I have found it best to have your clutch setting low and work your way up until it seats the screw correctly and engages the clutch. Depending on the drill, this can be many different settings, so I would not be able to recommend a setting.  

Unfortunately, I would not recommend using 1/2" MDF for your top and bottom, as this material has a lot of flex and would probably not give you the support you would want for your shelves. I would recommend using 3/4" to ensure it could hold up to weight needed. If you have any other questions, please let us know.  

You can also put a strip of wood to face off the fronts of shelves, top and bottom. This will help strengthen and make it look more finished.
 
KregCS said:

Miroslav, 

You can definitely use MDF and particleboard with pocket holes. However, you will want to be very careful when driving your screws. If the clutch is set too high, your screw will continue to drive and will come out the other side. I have found it best to have your clutch setting low and work your way up until it seats the screw correctly and engages the clutch. Depending on the drill, this can be many different settings, so I would not be able to recommend a setting.  

Unfortunately, I would not recommend using 1/2" MDF for your top and bottom, as this material has a lot of flex and would probably not give you the support you would want for your shelves. I would recommend using 3/4" to ensure it could hold up to weight needed. If you have any other questions, please let us know.  

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_