Kreg Owners' Community

About half the time I drive a screw into a pocket hole, the screw bites in and goes into the material, but doesn't tighten down.  It'll freely spin, even on a relatively low torque setting (10/24)

Other times, the operation works as expected.

This seems to occur most often with coarse 1 1/4" screws into 3/4" (1x4, 1x8) pine, but I seem to recall having the issue with the 2 1/2" screws (into 2-by) as well.


Does anyone have any suggestions as to what could be causing this? 

Thanks.

Views: 15199

Reply to This

Replies to This Discussion

I have experienced this as well. I agree that using a drill/driver gives less "feel" for the torque and I would use a very low torque to drive the screw to begin with to avoid a lot of manual turning and then finish by hand. It depends a lot on the wood used. I find that even in some hardwood there are soft spots that give the same problem.

An Old Timers solution for stripped holes in wood:

 

Back the screw out and stick a wooden match stick, toothpick, or sliver of scrap wood into the hole, if you think it neccessary - add glue into the hole and then re-insert and re-tighten down the screw slowly and carefully as the others have suggested.  Trim the matchstick/toothpick that extends beyond the screwhead.

 

(I learned that from 'Howdy' Olson, a friend, who passed more than a decade ago.  Took a bullet above the knee while running up a beach in the Pacific "oh that's me" - but it only slowed him down.  I recollect him each time I use his wooden match stick fix.)

 

Another tip for driving screws where I am concerened about splitting - I coat the screw with wax/parafin beforehand.

soft wet wood
I had a similiar issue.  I found that I did not set up the drill bit correctly.  On the jig I measured the depth from the drill bit tip vs where the drill bit began.  I was not getting the proper depth in the pocket hole.  It caused the screws to not enter the pieces of wood fully causing them to be a weak joint and also freely spin.  Especially, when using pine.
Use a drill with a clutch and torque adjustments.  Set the torque on low and clutch about 7-8 and test on scrap wood.  You may have to adjust the clutch setting up or down.

You might want to take a file and tone down the bite on the self tapping flange at the end -side of the screw, if the cutting flange is too wide it makes too large a hole for the threads of the screw to grip forcefully

 

 

Gene Knobloch

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_