The cabinet over the refrigerator is 30 inches deep and houses a large pull out that opens by pulling either of the doors above. It comes out over the refirgerator allowing the contents to be reached from the floor and a small step stool. No more crawling over the top of the refrigerator to reach items in the back of a cabinet.
Tags:
Projects: Custom Kitchen Cabinets
Favorite of 1 person
Comment
Thank you Claude for a nice compliment on my work. It still needs the crown molding that will be a custom molding about 12 inches in height. I am lookingforward to doing this molding as it will involve some planning and some cove cutting on the table saw. There will be some thumb nail molding and some dentel molding.
This is simply exquisite. I like the design . Once again, a combination of art and function.
Jay,
Great approach.
Thanks for your inputs.
Thank you Ken. This is something that I have been doing in most of the kitchen cabinet builds that I do anymore. All my customers are thrilled once they see how easy it becomes to add and remove cabinet contents from a cabinet that is located above a 6 foot tall refrigerator. Another good thing about this is that it is a deep cabinet rather than a standard debth upper cabinet. This cabinet takes advantage of the full depth of the refrigerator which in this case is 30 inches deep and sets low over the refrigerator taking away the common habit of sitting objects on top of the refrigerator where they fall off from the opening and closing of the refrigerator freezer doors. In some of these refrig cabinets, I will not glue in the cabinet bottom and build the cabinet in a way that the bottom can actually be lifted upward to allow for a taller refrigerator of the future. I leave the rail unglued as well so it can be removed and cut to fit the new higher installation and re-attached using the face frame screws. i have found from experience that he kreg screw will hold the bottom of a cabinet without gluing.
Note in the photo that I have extra wide lower rails. The doors are actually attached to the pull out with screws and can be removed to adjust the pull out height in the cabinet and still maintain door alinement. In the photos that I posted the doors look to be higher than the others, however this is an optical illussion as the doors are the same height as the upper ones on the pantry. The pantry sits 5 inches back from the refrig cabinets front. It this install the refrigerator slides in with 1/2 clearence from the cabinet bottom.
The big problem I have found is different refrigerator models make differenct hinge configerations. It is the top hinges that causes cabinet clearence problems. This is why I elect to approach leaving the bottoms of the cabinets so that I can modify them if the customer gets a refrigerator that is too tall for the opening.
Jay,
That pull-out drawer feature, in your overhead cabinets, is a ''great design'' approach.
Thanks for sharing.
Thank you Matin, This is a cabinet that I have been doing in almost every kitchen that I do. The way it works is that it has a large pull out on full extention slides that will pull out of the cabinet to a point that is infront of the cabinet. The sides of the pull out are cut down allowing a person the ability of reaching items from the sides. The doors are attached to the pull out.
These are very nice. Beautiful work.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
You need to be a member of Kreg Owners' Community to add comments!
Join Kreg Owners' Community