Kreg Owners' Community

Is there a industry standard to fridge height? Planning out cabinets and would like to use the space over my fridge too, but would like to make sure I am not screwing myself in the future when I replace the fridge with a new one....

Thanks

Views: 1454

Reply to This

Replies to This Discussion

Mike no there really is not as standard anymore.  They vary in width and height and configeration.  That is one of the most annoying things in building a set of cabinets is the refrig.  What I have done in the past is to build a cabinet that I know will be wide enough.  Since it is usually the height that does not fit I  leave the bottom and the lower face frame rail  unglued and pocket screwed so that I can take both the face frames lower rail off and  raise the bottom. If you build the doors short and take up the extra width using a wide lower rail in the face frame you can then replace the lower rail with a narrow rail to match up the bottom.  Most likely you will not have to redo the doors.  If you use this approach do yourself a favor and stain out and finish  an extra lower rail and just sit it in the back of a cabinet somewhere should you need it later.  That way the finish will be the same when you use it.   It is the easiest fix there is and should work without difficulties. 

To add to this if you pocket the screw the bottom into the sides from the bottom it is easy to remove the screws and they are hidden fro view by the installed frig.  Once you get the bottom back into position simply use a hand saw and cut the unused face frame stiles off flush with the bottom of the face frame rail.  Use a hand saw and cut the extra length unused portion of the cabinet sides off and for the very rear where you can't get room to move the saw back and forth simply use a air grinder with a wood rasp type bit and or use a sharp chisel and a forsener bit to remove the remaining wood.  In using the frostner bit drill it toward the adjoining cabinet and be careful not to over drill.  Making a series of cuts with the forsner bit rim against the bottom of the cabinet, you will have very little to remove with a chisel.  Once it is removed wipe on some stain and you are done.  Sounds more complicated that it really is but is a standard method I do anymore when building cabinets over a refrig.   

There is no specific industry standard for fridge height, as refrigerator sizes can vary widely between manufacturers and models. However, there are some common height ranges for refrigerators that you can use as a general guideline when planning your cabinet layout.

Standard height ranges for refrigerators include:

Top freezer models: 65 to 69 inches
Bottom freezer models: 67 to 70 inches
Side-by-side models: 67 to 70 inches
French door models: 68 to 70 inches
It's a good idea to measure your current refrigeration and the space you have available above it to ensure that any cabinets you install will accommodate your current appliance. Additionally, leaving a little extra clearance above the fridge can help ensure that you'll have enough space for any future models you might purchase.

Hey there! When it comes to fridge height, there isn't a strict industry standard, but there are common dimensions manufacturers tend to follow. However, it's always a bit of a bet when planning for future appliance replacements. Generally, refrigerators can vary in height depending on factors like style and brand. It's wise to leave some extra space above your current fridge to accommodate potential size differences in the future. Good luck with your cabinet planning!

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

The Pocket Hole Joinery Book - Review

Posted by Daris R. on August 27, 2024 at 8:29pm

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_