Tags:
Ken Guenther said:
Hello Ash ;
There are a number of good routers on the market today, the hottest and newest is the Bosch MRC23EVSK. Take a close look at this one, it looks like a super tool. Saw a video where they set the tool, with no bit, on a bench top and let it run at full speed for over 3 minutes. It never moved.
kenny in Sundre, AB.
Hello Ash;
I guess I am a bit of a turn coat because I just bought an M12VE Hitachi Router. While I think the new BOSCH router is the greatest, when I compared the $390.00 / $420.00 price tag against KMS's price tag of $229.00 on the Hitachi it wasn't much of a contest! I have a corded Hitachi D10VH 3/8" drill, a DS18DL cordless drill, and a C10FHS SCMS, all of which have given me reall good service.
kenny at Sundre
Hi Ken - nuthin at all wrong with Hitachi stuff. I have their M12VC and it's one sweet little unit. I also have several of their nail guns and just reluctantly upgraded from their 10" compound miter saw. I only upgraded as I needed a slider and got a deal on the new Triton.
Incidentally, I read your previous post about the Bosch running untouched for 3 minutes with no vibration. So happens my new Freud 3000 arrived the next day so I tried that with the 3 1/4 HP Freud and had the same result. Downside is it won't fit under my benchtop router table so gotta build or buy a new table.
Ken Guenther said:
Hello Ash;
I guess I am a bit of a turn coat because I just bought an M12VE Hitachi Router. While I think the new BOSCH router is the greatest, when I compared the $390.00 / $420.00 price tag against KMS's price tag of $229.00 on the Hitachi it wasn't much of a contest! I have a corded Hitachi D10VH 3/8" drill, a DS18DL cordless drill, and a C10FHS SCMS, all of which have given me reall good service.
kenny at Sundre
Thanks for all the discussion. I have settled for MLCS Router table and the Dewalt VS Combo for under $400. I am in process of putting everything together.
Hi Ash - Good Luck, I've been using the little MLCS benchtop portable table (the one with folding legs) for nearly two years now. Did make a couple of modifications to the fence but other than that it has worked well for me. Good Luck
Ash Parikh said:
Thanks for all the discussion. I have settled for MLCS Router table and the Dewalt VS Combo for under $400. I am in process of putting everything together.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service