Introducing the Kreg Rip-Cut™

[KregRep]

 

 

Introducing the Kreg Rip-Cut™

Available at Kreg Dealers everywhere

$34.99

Ripping down large panels into smaller more manageable workpieces can be one of the trickiest, most intimidating, and expensive steps of any wood project. Even for experienced woodworkers ripping with the nicest table saws, you’re still forced to lift large heavy panels, balance them carefully to avoid binding and bowing, while at the same time trying to support the finished workpieces  and waste material as they exit the saw.

 

There is a faster way. There is an easier way! There is a better way.

Introducing the Kreg Rip-Cut™.

 

The Rip-Cut™ is an incredibly handy tool which speeds and simplifies the process of ripping down large plywood and MDF panels. No more taking your work to the saw, instead take the saw to your work. No measuring, no marking, no chalk lines – the Rip-Cut™ quickly and easily attaches to almost any circular saw, letting you cut pieces up to 24” wide with tremendous accuracy.

 

The Rip-Cut™ is a no-nonsense, straight forward, precision accessory for your circular saw that is so incredibly affordable it will pay for itself in no-time. It features a durable design including a solid aluminum guide rail, ultra-durable impact resistant plastic, an easy-to-read precision adjustable scale, and a reversible guide arm which works whether you’re left or right handed. It’s a super easy, precise, and affordable way to break down large panels for almost any project.

 

• Connects to almost any circular saw – right or left blade
• Reversible Guide Arm for Right or Left Hand Use
• Makes rip cuts up to 24” wide
• Rip sheets of plywood in half – in just one cut
• No measuring, marking, and no chalk lines
• 100% Guide support through entire cut
• No need to remove Rip-Cut™ when doing cross cuts
• Quick and accurate adjustments – no tools required
• Lightweight/Sturdy Design for use on the jobsite

 

Materials:

High Quality Aircraft Aluminum

Impact Resistant Plastic Polymer

Aluminum Guide Rail:

3" wide x 30" long

 

Saw Sled

6 1/2" x 8 1/2" saw platform

Guide Arm:

2" wide x 10" long

Minimum 5" edge bearing at blade entry

Minimum 3" edge bearing at blade exit

 

Cut Width:

Maximum 24"

 

Check out the Rip-Cut on www.kregtool.com!

http://www.kregtool.com/RipCut-Prodview.html

 

 

 

 

 

[Daryl]

How does it work if you need to do a 45 deg beveled rip cut?

[Kevin]

Maybe a mold at the front/leading edge, connected to a vacuum source could be added to enhance the device and make it more appealing. It would be a challenge to create an adaptor for all of the circular saws on the market today. 

David Shinkle said:

My issue with circular saws is dust collection.  This looks like something that would make it easier to rip panels.

[Scott Bastian]

I like the universal fit for different saws.... and I see a small orange pointer is there adjustments to the pinter to get it zeroed out?

 

Another thought, will this be  adaptable to a router for making long daddos?

[jesse atkins]

This is useless unless it's 5 or ten bucks. I've build jigs on the job from scrap wood in 10 minutes that work way better, and the plastic give it maybe 2 weeks on the job

 

[KregRep]

Kevin,

Thanks for your comments. Actually, depending on your saw, there's usually between 5-8 inches of guide arm support before your blade enters the workpiece. There's a tremendous amount of support at the beginning and end of the cut thanks to the extended Guide Arm.

KregRep

Kevin said:

 It seem like the leading edge of the guide is about 1 1/2 inches and will rely on the user to make sure that they keep a steady hand when starting/ending.

[Den]

Guess it's OK if the cost is under 20 bucks. It seems okay if the matieral has a straight edge to start with.

I might as well pay the guy at the home depot .50 cents a cut to make a 4x8 sheet smaller. I've had good luck with my T-square to make straight cuts.

[Randy Caswell]

That's it.....? That's what the two day wait was for?? Sorry, but after a series of nice tools, which I own, this is a serious dud.

[Kevin]

Seems like its under $40, based on some of the tool website that have it already listed for sale. 

Andy Wells said:

Got any idea on the price?  Look very affordable and easy to use.  I've been waiting for this for a long time.

[David Pummill]

Just another shop toy!!  I like toys!

[Kevin]

Great idea for routers ................. :)

Scott Bastian said:

I like the universal fit for different saws.... and I see a small orange pointer is there adjustments to the pinter to get it zeroed out?

 

Another thought, will this be  adaptable to a router for making long daddos?

[Dave M]

Is says that you can cut up to 24" so I do not think you can make the two 4X4

Ronny Roach said:

I can't see how you can cut a 4x8 sheet in half in order to have two 4x4 

[chris biggs]

I got an email this week saying something along the lines of an amazing new tool from kreg. Well this can't be it . Not very clever as others have mentioned and I can't see it being perfectly stable while cutting. Stick to your pocket hole jigs kreg they are great.