Kreg Owners' Community

Doug Nale's Discussions (15)

Discussions Replied To (13) Replies Latest Activity

"I have a router/table.  My issue always seems to be in setting up my fence to be nic…"

Doug Nale replied Apr 5, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"The 40 tooth diablo that I got was $27 or $29, under $30 for sure.    I might have t…"

Doug Nale replied Apr 5, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"I used 1 1/4" regular steel tube, square stock.  Actually HD didn't have enough of w…"

Doug Nale replied Apr 5, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Ouch!  $130 for that???  I thought this was expensive enough of a hobby here. "

Doug Nale replied Apr 4, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"It's tapped for 1/4" 20. So I put a bolt and washer/nut combo on there so it is supp…"

Doug Nale replied Apr 4, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Here is the link to the hf base.  It's $40 but use a 20% off coupon and it's $32.  I…"

Doug Nale replied Apr 4, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Thanks Jim. This thing feel like a tank. I put it down on the supports and I don't s…"

Doug Nale replied Apr 3, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Now does anyone know what bolt should be where the motor pivots in a guide? I put a…"

Doug Nale replied Apr 3, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Think I have it."

Doug Nale replied Apr 3, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

"Well it is complete! Much much sturdier than my other one. If I can figure out how t…"

Doug Nale replied Apr 3, 2013 to Keep current table saw or use an older one

35 Apr 5, 2013
Reply by Ken Darga

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Concealed Hinge Jig Setting Confusion

The Kreg Concealed Hinge Jig has a setting for the distance from edge of the door to the nearest edge of the 35 mm cup hole. This can be set as 3, 4, 5, or 6 mm.Later in the instruction there is a table that converts the distance from the edge of…Continue

Started by Ken Kortch in Kreg Jig® Operation Oct 11.

Help with old Rip-Cut(tm)

I have an old Rip-Cut which I bought many years ago but did not set.  I seem to have lost the instructions, if I ever had them.I cannot figure out which bolts are match with the nylon-lock screws.This unit is old enough that the current instructions…Continue

Started by Sean in Other Kreg® Products Oct 4.

Product Reviews

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 1 Comment

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_