Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Miter Corners for Picture FramesI have been making custom picture frames for years. When I recently became reaquainted with my Kreg Jig I realized that I could save some t… Started by Andrew Pensavalle |
14 |
Dec 30, 2015 Reply by Elizabeth Leveques |
an old man looking at a new hobbyI appreciate the comments and willingness to help. Like some others I just got a kreg jig jr and it's too cold to get outside and try it. L… Started by Jim Osteen |
5 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Kreg DocumentationIn some of these posts I've seen pages from some documentation that looks quite useful. My question is: Where is this documentation to be… Started by Tim Rude |
7 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Setting the collar 1-1/4" vs 1-1/8"Hey fellas, I work for a Kreg Tool retail dealer and a customer pointed out a funky flaw on the bench top clamp today. Using the drill bit… Started by Mark Stephens |
6 |
Dec 30, 2015 Reply by Elizabeth Leveques |
How to trick the jig, and use 7/16 wood ?Has anyone found how to trick the jig so they can use 7/16 wood? Started by Paul Boehme |
3 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Need some help with ash woodHello all Dave here has anyone here worked with Ash wood this is the first time I’ve worked with it but some people say its like soft maple… Started by David Dean |
4 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Is there a place to keep the allen wrench?I've got a loose part and wish the jig (or case) had a place to keep the Allen Wrench. Am I missing something? Started by Bob Sanders |
10 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Proper measurementHi, Folks-- It turns out that the wood I'm working with is 23/32nds. What would be the correct measurement from the shoulder of the bit fo… Started by Ed Hack |
13 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Making PanelsI know Kreg recommends that members of a panel not exceed 6 inches. Has anyone exceeded this? I am thinking of joining pieces that are 12 i… Started by Andrew Pensavalle |
11 |
Dec 30, 2015 Reply by Elizabeth Leveques |
Wood movementI think I may have read a response to this question in the forum but could not find it again. My question is in regards to wood movement an… Started by Will Middleton |
2 |
Dec 30, 2015 Reply by Elizabeth Leveques |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service