Kreg Owners' Community

Kreg Jig® Operation (277)

Discussions Replies Latest Activity

Newbie, need help with 45 degree cuts

Any advice/ secrets / when it comes to setting up the jig when connecting 2-45degree boards?

Started by Russell

7 Dec 30, 2015
Reply by Elizabeth Leveques

Drill Hole Not smooth

I just purchased the K4 Master System. I made a few drill holes, but they are not smooth.  I made sure the wood is clamped tightly to the j…

Started by Jae Park

5 Dec 30, 2015
Reply by Elizabeth Leveques

Uneven clamping results

No matter what pressure I clamp the two mating surfaces, I'm having a consistent uneven surface issue after clamping and screwing i.e. eith…

Started by bfortino

9 Dec 30, 2015
Reply by Elizabeth Leveques

Pocket holes in tight places?

Hello all!I am new to woodworking and also new to this forum. My second Kreg project was some basement storage cubbies.  During assembly I…

Started by Scott Zwiener

11 Dec 30, 2015
Reply by Elizabeth Leveques

K3 Master System Component Storage

Would someone please turn on the light for me?   My K3 MS came with a nice blue storage box but I can't figure how to organize my K3 compon…

Started by Don Spero

2 Dec 30, 2015
Reply by Elizabeth Leveques

drilling

When I set my drill for the proper width of wood etc I notice the tip if the step drill barely if at all pierces the bottom of the wood. I'…

Started by Mike Swaga

3 Dec 30, 2015
Reply by Elizabeth Leveques

deck 2x2 spindles

I attached deck 2x3 spindles with the kreg blue scres and pocket holes two screws top and bottom. They are very secure. Unfortunately kreg…

Started by Joe

1 Dec 30, 2015
Reply by Elizabeth Leveques

Using Kreg jig instead of a nailer for framing

I'm planning to build an office counter using 2x4's as the frame.  Can I use the Kreg jig to build the overall frame?  Is it an overkill or…

Started by Teriyaki

7 Dec 30, 2015
Reply by Elizabeth Leveques

Introduction & Question

 HI    My name is Jim I live in CT and consider my self a moderate woodworker,  I have been doing woodworking on and off since my first woo…

Started by Jim Lozinski

9 Dec 30, 2015
Reply by Elizabeth Leveques

Help! Joints not tight!

i am a first time user of the kreg jig. tried to drill a few holes with no problem but i had a lot porblem with tightening with the screw.…

Started by jc

6 Dec 30, 2015
Reply by Elizabeth Leveques

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Wall cabinet 14-16" deep

I'm looking for plans, especially the cutout pieces on a 4' x 8' sheet of plywood for wall cabinets that are deeper than the standard 12". Anyone in the community adapted Kreg plans for 12" to a deeper cabinet?Thanks, HenryContinue

Tags: cabinets, Wall

Started by Henry Beun in Kreg Jig® Projects Jul 25.

Joining 1.5" thick red oak butcher block

Hello. I am a beginner DIYer and new to this community. I am searching the best way for joining 1.5 inch thick Red Oak butcher block counter top. I need to join 2 boards perpendicular for L shape. Would 1 1/2 fine thread screws with 1 1/2  jig setup…Continue

Started by Aya Kaiho in Beginners' Zone Jul 17.

Product Reviews

Kreg Jig Dust Collection Attachment

1st impression when you hold this attachment in your hand:  "not much to it", Kreg sure is makin' $$ here.



Then I installed it.. perfect fit, leaves just enough room to adjust the setting screw on my K4.



Then the real test, hook…

Continue

Posted by Grampy Meyer on February 23, 2020 at 11:36am

My K4 Master System

I picked up the K4MS from Home Depot about 3 months ago, I was looking for a small filing cabinet for under my desk and nothing I looked at would fit or they wanted big money for it, my wife said “why don’t you just build your own then you will…

Continue

Posted by Randy W. Lush on August 25, 2019 at 12:30pm

© 2020   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_