Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
There's a possiblem.I also had the same problem. I followed all the directions and tripled checked all my marks. I got to the point where finally,I sough… Started by David Briseno |
0 | May 23, 2011 |
Does Deck Jig make stainless screws unnecessary for cedar decking??Normally, stainless screws are used for cedar decking when face screwing to prevent discoloration/staining. Since the Deck Jig drives the s… Started by John Burke |
3 |
May 22, 2011 Reply by John Schaben |
Plywood and the Mini KregThis might just be a problem with 1/2 inch birch plywood. I finally got the Mini secured well enough to try it - which is a story in itsel… Started by elpasobooks |
3 |
May 20, 2011 Reply by John Schaben |
Can the Kreg system be used with Plastic?I have a project in mind for my boat using the type of plastic that cutting boards are made from only this is 3/4" thick. Will the Kreg sy… Started by Robert Redman |
18 |
May 10, 2011 Reply by Marc St. Pierre |
Which Setting on Drill Guide for different material thicknesses?I am attaching a 3/4 inch piece to a 1-1/2 inch piece (2x4). Which Piece do I use to determine my Drill Guide setting , the 3/4 inch or th… Started by D S |
9 |
May 9, 2011 Reply by Skipper Smith |
Kreg screws on melamineHello all, I'm about to build some kitchen cabinets using melamine. Can coarse thread screws be used on it? Will it hold? All opinions… Started by Richard Ljungquist |
12 |
Apr 30, 2011 Reply by Jay Boutwell |
Wooden plugsUntil recently, I have not had occasion to use the wood plugs to cover the screw holes. I found them rather difficult to use. I applied g… Started by Harold Buzzell |
12 |
Apr 25, 2011 Reply by wilma44 |
Can you use any Kreg screw with any kreg jig? + Kote questionHi all; I bought an older, metal kreg jig off of craiglist a few weeks ago. The job I'm using it for is pretty simple, I'm joining a bunc… Started by Allochthon |
0 | Apr 15, 2011 |
Is MDF Strong Enough to make a Pocket Hole in ?I am making a small workbench with MDF top and I want to put pocket holes in the underside to secure solid wood edge banding around the out… Started by D S |
21 |
Apr 14, 2011 Reply by Steve Osterday |
ScrewsI am attaching skirts to table legs, and the skirts are one inch thick pine. I know I am supposed to use the coarse thread, but what is the… Started by Michael Hobert Edwards |
2 |
Apr 3, 2011 Reply by Michael Hobert Edwards |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service