Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
What is the best wood to use for a router table top?I want to build a router table for my first project in my new shop after I finish it sometime this summer. What would be best to use to mak… Started by Leslee |
12 |
Apr 20, 2013 Reply by ray vile |
Jen Jensen's memorial Service setKnowing that Jens has many friends on the Kreg Jig Community I wanted to pass along the information about his Memorial Service . For thoe… Started by Jay Boutwell |
3 |
Apr 19, 2013 Reply by Justin |
Homemade router tableI am in the process of making my very own router table. I saw plans where someone was repurposing a old kitchen countertop. Well, I have fo… Started by Greg K |
11 |
Apr 17, 2013 Reply by Ken Darga |
Harbor freight dust collectorI have been looking at a dust collection system for a small shop( only about 400 sq feet) and I ran across the harbor frieght system. Does… Started by Jeremy Sanders |
7 |
Apr 16, 2013 Reply by George Santiago |
How to read specs on power toolsGuys, Im looking to purchase a dust collection system. Im looking at the JET system. The specs show: Motor Power 1-1/2 HP Motor Pha… Started by Russ |
3 |
Apr 16, 2013 Reply by Joseph Scharle |
Kreg Jig K3Picked up a K3 today on CL for $50. Very slightly used, came with drill bit, drivers, etc., plus an almost full box (500) of 1 1/4" coarse… Started by Fins59 |
18 |
Apr 14, 2013 Reply by Rick |
Rockler Hold Down ClampsHas anyone used these Rockler Hold Down Clamps with their Universal T-Track????? The bench I will be installing these in has drawers, whic… Started by Matt B |
7 |
Apr 10, 2013 Reply by Ken Darga |
Wood Movement After SealingHowdy All, I have a question about what type of movement should be expected from wood once it's been sealed by, let's say, three coats of p… Started by Troy |
6 |
Apr 6, 2013 Reply by Ken Darga |
Drawer slide mounting locationOk, let's see if the "there's no such thing as a stupid question" rule applies: When installing side-mount, ball-bearing drawer slides, whe… Started by Russ Haynes |
3 |
Apr 5, 2013 Reply by Russ Haynes |
Keep current table saw or use an older oneI'm in a dilemma myself. Probably 5-7 years ago my wife bought me a craftsman mobile 10" table saw. It's fairly similar to the one they h… Started by Doug Nale |
35 |
Apr 5, 2013 Reply by Ken Darga |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service