Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Assembly/Finishing HelpI'm in the process of building an oriental-inspired coffee table similar to the picture below and would like some opinions from other woodw… Started by Don Foley |
2 |
Aug 13, 2014 Reply by James P. Cottingham |
What's the deal with Harbor Freight?I am new to the notion of Harbor Freight. One opened near me recently. I needed a rubber mallet for some furniture repair and refinishing… Started by Keith Woythaler |
14 |
Aug 12, 2014 Reply by Ken Darga |
Strength of Rubber Wood Finger-Joint SheetHi All, I am thinking of cutting 2-inch rails from rubber wood finger-joint sheet, and using those for cabinetmaking (cabinet with frame).… Started by Chandra Shekhar Pullella |
4 |
Aug 11, 2014 Reply by Chandra Shekhar Pullella |
Position of Pocket Holes for StrengthI am putting some 3/4-inch plywood shelves in a closet that already has vertical plywood dividers. I am using pocket holes instead of shelf… Started by Jerry |
5 |
Aug 8, 2014 Reply by ron abel |
Side Board TableLooking to make a side board table with a wine rack in the middle, two upper draws, and two cabinets. Any body have any plans or suggestion… Started by Mike rignola |
3 |
Aug 8, 2014 Reply by Rita B. |
The New DB210 Pocket-Hole MachineHi Kreg Jig Members, I was wondering if anyone has purchased the new Kreg DB210 Pocket-Hole Machine yet. If not, you are missing out on… Started by Jay Boutwell |
1 |
Aug 4, 2014 Reply by Gary roofner |
Hand Plane Bevel AngleHello everyone, I am in the process of restoring my grandfather's Stanley Bailey No 3 plane. I am very new to the hand tool scene; Do all… Started by Stephen |
5 |
Aug 2, 2014 Reply by Ken Darga |
Hole DrillingSo much to learn and when things crop up, this is my go to place for answers. From time to time in a project or house hold repair, I have… Started by Rita B. |
25 |
Aug 2, 2014 Reply by Ken Darga |
Can I join timber thicker than 38mm?Hi, I'm looking in my project to build timber frame from 2" x 4", can I join board as thick as 50mm? What screws would you use? Many tha… Started by Jakub Karczewski |
1 |
Jul 31, 2014 Reply by KregRep |
Misrepresentation and TrustIt seems that I am always writing about something of which I should not have to. The last time it was about the spam appearing here and… Started by Jay Boutwell |
8 |
Jul 30, 2014 Reply by Gary roofner |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service