Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Router table helpOk another newbe question. I'm thinking of buying a router table, but I'm confused about the mounting of it. Will i need to drill the plate… Started by Steve Bennett |
5 |
Jul 19, 2011 Reply by Gary roofner |
Help!Ive recieved JB's very expensive reversible John Boos butcher blockhttp:http://www.amazon.com/John-Boos-Reversible-Maple-Cutting/dp/images/… Started by angie brashears |
7 |
Jul 18, 2011 Reply by Ray Romero |
Wood widths are just not quite what they should be...I searched at my local Big Box through nearly an entire stack of 1x6s. They were all 1/16th shy of .75" thick. I went ahead and bought a fe… Started by June Solomonson |
7 |
Jul 16, 2011 Reply by John Schaben |
Disaster has struck my Inlay Table Jun 2011 and 4 Veneer table top all in 1 dayCan you beleive it! I was on my third finishing coat on the table top and next morning I found the surface finish resembled sandpaper, mo… Started by Robert Brennan |
4 |
Jul 14, 2011 Reply by angie brashears |
Pocket holes to join side rails of bed to posts?Does anyone know if it's possible to use my Kreg jig to join 2x6 bed rails to 4x4 posts using 2.5 inch screws? I was thinking of 3-4 holes… Started by Sara Lynn Eastler |
11 |
Jul 7, 2011 Reply by Sara Lynn Eastler |
Settings for 1/2" material not working outI working with 1/2" (0.5") birch plywood and attempting to make some drawers. Set my Kreg drill bit stop to 1/2" based on the gauge on the… Started by Joe Ghatta |
6 |
Jul 1, 2011 Reply by Joe Ghatta |
2X4 vertical railing attached to 4X4 postI plan on a deck railing with a vertical 2x4 lower rail with 3/4 aluminum balusters and a vertical 2x4 top rail. Which would be best to at… Started by Charles Vanderpool |
0 | Jun 29, 2011 |
Are narrow cabinets possible using the Kreg Jig?Hi everyone. I'm new to making cabinetry. My project is mostly designed, cut, and painted but I haven't put the pocket holes into my parts… Started by Mayo Pardo |
10 |
Jun 29, 2011 Reply by David Sechrest |
secret compartmentsi want to start adding secret compartments to all my new projects, no need to hide anything. just think it will be interesting to add them.… Started by steve kidd |
3 |
Jun 24, 2011 Reply by steve kidd |
What is the best way to square a Frame?I am making an 75" x 40" frame with 2X4s and want each corner square. Now if I was using nails I would place one in each joint then measu… Started by Larry Mathews |
22 |
Jun 19, 2011 Reply by Steve Bennett |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service