Kreg Owners' Community

As a beginner in the world of woodworking i have a lot of things to learn to be able to build something. I have some tools that i purchased and some were gifts from my husband. But to be able to start with a project what type of wood should i use price matters since i will sure make a lot of mistakes in cutting. Hope to find an answer from this community....

Views: 1259

Reply to This

Replies to This Discussion

It depends what you’re going to build but to practice I’d suggest pine and MDF. Both are inexpensive, forgiving and great to play with!

Have fun!

I would start out with pine, it's easy to cut and alot cheaper than the other wood that is available at the bigger home centers, these stores also have a scrap wood bin located close to where they do the lumber cutting, you can find some nice pcs. of wood there for next to nothing.

 

i agree with all the postings, here is another option. try a local cabinet maker for small scrap pieces for free, you might get a nice assortment of wood. dont expect enough wood to make a project but you might get some to experiment with.

 

I agree with Sarah as I was at my local Habitat Restore the other day and picked up 2x4s for my model railroad layout for next to nothing!! I also found a low flow toilet a few months ago for 1/2 the big box boys!
I had forgotten about the habitat store. I have one about 30 miles away from me and last time i was there i notice alot of 2x4 and 2 x6 and 8 so i guess its time for me to make a trip there
THANK YOU ALL FOR ALL YOUR OPINIONS AND I WILL LITERALLY DO WHAT U SAID....CAN'T WAIT TO START ON MY FIRST PROJECT...WORKBENCH....I'LL POST PICS WHEN I START ON IT....AGAIN, THANK YOU....

I also agree with TOMBOY, if your re-store carries that kind of product it's an excellent source for inexpensive wood.  I've even bought a couple of solid wood doors and ripped them down on a table saw to make shelving, etc. 

Apart from that, MDF will give you a forgiving product with a smooth surface to work on.  SPF (spruce/pine/fir) plywood is a good product for building dressers/cabinets or what have you.  Not the kind of thing you would use if you were a craftsman (which i am not) but it will still provide a nice end-product with sufficient sanding.

 

Good luck and welcome to the world of wood-butchery ;)

Hi All,

 

I've got the same question as Wenjie. Not sure what wood to use for a 8'x24"x22" TV Stand. I'm planning to make that into 2 4' boxes(side by side) since it'll be way too heavy otherwise. Is it possible to go hardwood on top and then use clear fir or something for the rest? I'd like to minimize weight but keep the same overall look. Planning to use a Java Gel stain or something dark on the whole piece after.

 

Thanks!

Anthony

Attachments:
While I am just a beginner I dont see why you cant use dirrent wood. After all most cabinets are plywood carcass and then a nice wood face frame.

Hi Anthony,

 

My opinion, build it out of plywood.  You can get amazing products out there, and a lot of people think that in order to do it correctly and make it look right you'll use dimensional lumber or specialty hardwood.  Birch or Maply plwood can be smooth on both sides and allow you create a solid carcass to build off of.  For myself, you can bet, if it's got a cube in the design, i've made it out of plwood. 

 

3/4" will give you the strength and a burly look that will help hold weight and keep from bowing. 1/2" for shelving if you want to shave off a couple pounds, 1/4" for the back.  As for the exposed edges, pick up some veneer edging (iron on) or, if you're looking for something more substantial, pick up some wood and rip down 3/4" wide strips and nail/glue them in place, sand them a little and then paint.  You can also use wood filler, spackle or what have you and fill the edge that way.  A little sanding with 220 grit or so afterwards and you've got a finished edge....i use this for exposed edges when they are within the cabinet as the finish is never perfect.

anthonychan105 said:

Hi All,

 

I've got the same question as Wenjie. Not sure what wood to use for a 8'x24"x22" TV Stand. I'm planning to make that into 2 4' boxes(side by side) since it'll be way too heavy otherwise. Is it possible to go hardwood on top and then use clear fir or something for the rest? I'd like to minimize weight but keep the same overall look. Planning to use a Java Gel stain or something dark on the whole piece after.

 

Thanks!

Anthony

Interesting, I didn't think of using plywood out of something like maple! I'll look around and see what's available. Hopefully that'll save me a few bucks too! Stay tuned for pictures within the next weekend or 2.

 

Thanks!

Anthony

 

Geoff Simpson said:

Hi Anthony,

 

My opinion, build it out of plywood.  You can get amazing products out there, and a lot of people think that in order to do it correctly and make it look right you'll use dimensional lumber or specialty hardwood.  Birch or Maply plwood can be smooth on both sides and allow you create a solid carcass to build off of.  For myself, you can bet, if it's got a cube in the design, i've made it out of plwood. 

 

3/4" will give you the strength and a burly look that will help hold weight and keep from bowing. 1/2" for shelving if you want to shave off a couple pounds, 1/4" for the back.  As for the exposed edges, pick up some veneer edging (iron on) or, if you're looking for something more substantial, pick up some wood and rip down 3/4" wide strips and nail/glue them in place, sand them a little and then paint.  You can also use wood filler, spackle or what have you and fill the edge that way.  A little sanding with 220 grit or so afterwards and you've got a finished edge....i use this for exposed edges when they are within the cabinet as the finish is never perfect.

anthonychan105 said:

Hi All,

 

I've got the same question as Wenjie. Not sure what wood to use for a 8'x24"x22" TV Stand. I'm planning to make that into 2 4' boxes(side by side) since it'll be way too heavy otherwise. Is it possible to go hardwood on top and then use clear fir or something for the rest? I'd like to minimize weight but keep the same overall look. Planning to use a Java Gel stain or something dark on the whole piece after.

 

Thanks!

Anthony

Pine, Maple, Birch, Oak... Your local big box DIY store will definately carry the first 4...don't forget specialty wood stores tho', you could find something cool like "Bamboo" plywood, bending plywood any and all types of exotic cabinet-wood....it's SO EXCITING!

 

ok, i'm done

 

anthonychan105 said:

Interesting, I didn't think of using plywood out of something like maple! I'll look around and see what's available. Hopefully that'll save me a few bucks too! Stay tuned for pictures within the next weekend or 2.

 

Thanks!

Anthony

 

Geoff Simpson said:

Hi Anthony,

 

My opinion, build it out of plywood.  You can get amazing products out there, and a lot of people think that in order to do it correctly and make it look right you'll use dimensional lumber or specialty hardwood.  Birch or Maply plwood can be smooth on both sides and allow you create a solid carcass to build off of.  For myself, you can bet, if it's got a cube in the design, i've made it out of plwood. 

 

3/4" will give you the strength and a burly look that will help hold weight and keep from bowing. 1/2" for shelving if you want to shave off a couple pounds, 1/4" for the back.  As for the exposed edges, pick up some veneer edging (iron on) or, if you're looking for something more substantial, pick up some wood and rip down 3/4" wide strips and nail/glue them in place, sand them a little and then paint.  You can also use wood filler, spackle or what have you and fill the edge that way.  A little sanding with 220 grit or so afterwards and you've got a finished edge....i use this for exposed edges when they are within the cabinet as the finish is never perfect.

anthonychan105 said:

Hi All,

 

I've got the same question as Wenjie. Not sure what wood to use for a 8'x24"x22" TV Stand. I'm planning to make that into 2 4' boxes(side by side) since it'll be way too heavy otherwise. Is it possible to go hardwood on top and then use clear fir or something for the rest? I'd like to minimize weight but keep the same overall look. Planning to use a Java Gel stain or something dark on the whole piece after.

 

Thanks!

Anthony

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_