Kreg Owners' Community

What is the difference between Particle Board and MDF?

I'm just wondering what the differences are between particle board and MDF?  MDF is more expensive and I was wondering why.  What applications would you use them differently? I'm a beginner woodworker and thought that you could help me understand the difference so that I can purchase the right material for the projects.  I'm always looking to save money. . .  any help you can give will be much appreciated.  Thank You.

Views: 21850

Reply to This

Replies to This Discussion

The boards sag as result of ''overloading".

Most particle boards, included with the metal storage framed shelving, is 3/8" thick.

A 24x36 rack will support an 800lb load---evenly distributed amongst all the 4-5 shelves.

3/8" thick is adequate to support a 200lb evenly distributed load, per shelf 24x36".

Option: 

Install thicker boards, just lay it atop the thinner boards.

NOTE: If using sheet material, it'll need to be cut to size, to fit between the upright frame members.

BTW

The back end of an automobile will sag, and perhaps collapse the springs, when the trunk is loaded/filled with 80lb bags of concrete.



RichardB said:

I have some shelves from Home Depot. The frame is heavy metal, but the shelves are either MDF or particle board. All the shelves that had any weight on them are all sagging. I've replaced most of them with pine boards. I wouldn't waste any more of my money on either of those products. They have no strength - weight/humidity/moisture is their enemy, and they cave far to easy. 

That stuff seems to sag from its own weight. I've stored items that are very light in weight, only to see the shelves sag. 

Rita B. said:

Lorrie, about your particle board shelving, you will want to add some additional bracing because they will sag over time.  Attaching a straight board across the front of each shelf helps too.   I purchased metal strips designed exactly for that purpose on some of my heavy use shelves.   I learned how quickly they can sag the hard way :)

I have particle board shelving, 3/4 x 12 x 4-8 ft sections, on shelf brackets spaced at 16"---

Some shelving has been up for over 25 years---no sagging problems.

Some shelves are loaded with books.

Some shelves support tool boxes, and the like.

To support "heavy loads", 2 such shelves, (double thickness of 3/4" thick material), can be used.

Any shelving material, whether wood or metal, to prevent sagging, needs to be adequately constructed, to support the weight of the material being stored on the shelves.

Supporting heavy loads, such as books, a 1x3 cleat can be installed on the wall or back edge, on the underside of the shelf, to resist sagging.

A support, such as a 1x2 along the front edge of the shelf, orientated 90 degrees to the shelf edge, and located on the underside of the shelf will provide additional support of the shelving, so as to resist sagging.

There are various suitable joinery methods that can be used to add support to shelving, to increase their load carrying capabilities.

No.  What kind of adhesive?

Ken Darga said:

Rick,

Have you ever used thinned down waterproof adhesive, to seal the exposed surfaces of particle board material?

Like Ken said, PB needs support every 16 in.  The fact that long boards are used also helps. 

I use plywood for nearly all utility shelving.  It helps to put a couple coats of poly on it to prevent stains.

3/4 in thick boards are slightly stronger than 3/4 in thick plywood.  Note that plywood is much stronger with the grain than against it.  The guy who built my sun porch obviously didn't know that since he ran the sheathing parallel to the rafters.  Ugh!

Even though each shelf material has its own modulus, note that its resistance to sag is a cube function.  In other words, under similar load conditions, doubling the thickness of the shelf reduces its sag by 8 times.  This, of course, only works if the shelf is one member.  Stacking 2 similar boards only reduces the sag in half.

RichardB said:

That stuff seems to sag from its own weight. I've stored items that are very light in weight, only to see the shelves sag. 

I once found this on-line "Sagulator" ... if you find it useful:

http://www.woodbin.com/calcs/sagulator.htm

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_