Kreg Owners' Community

Has anyone else had any issues with the new Zinc screws from Kreg? I've never had a problem before with the Bronze screw but my very first zinc screw snapped right of in one my walnut face frames! Frustrating to say the least...I do have a box of 5000 bronze screws left but it's discouraging to see Kreg replace a great product with an inferior one.

 

-RM

 

Views: 714

Reply to This

Replies to This Discussion

I'm sorry to hear that you have had an issue with our screws.  I was curious if you have used any other screws in that box.  I'm just trying figure out if it was just one screw that was defective or if it was the whole box.  Either way if you would send me your shipping information and the screw that you had issues with in a private message I would be more than willing to send you a replacement box. 

''hydrogen embrittlement''  can occur during various manufacturing operations. 

Electroplating is a major cause of hydrogen embrittlement.

The result of unintentional introduction of hydrogen into susceptible metals during forming or finishing operations and increases cracking in the material.

 

 

Hi KregCS,

 

I really appreciate your offer and standing by Kreg products. I guess my frustration with the new screws was the fact I was assembling an angled walnut face frame when the screw snapped off causing a major inconvenience. It surprised me because I have driven thousands of the bronze screws before without an issue and I want to have peace of mind that the new screws are manufactured to the same quality. Thanks for your feedback!!

-Ryan
 
KregCS said:

I'm sorry to hear that you have had an issue with our screws.  I was curious if you have used any other screws in that box.  I'm just trying figure out if it was just one screw that was defective or if it was the whole box.  Either way if you would send me your shipping information and the screw that you had issues with in a private message I would be more than willing to send you a replacement box. 

Thanks Ken! It could have been a rare occurrence then. It's just that the bronze screws looked like great quality.

 

-Ryan
 
Ken Darga said:

''hydrogen embrittlement''  can occur during various manufacturing operations. 

Electroplating is a major cause of hydrogen embrittlement.

The result of unintentional introduction of hydrogen into susceptible metals during forming or finishing operations and increases cracking in the material.

 

 

Ryan,

''hydrogen embrittlement'' is not a rare occurrence.

Ryan McLaughlin said:

>>> Thanks Ken! It could have been a rare occurrence .../p>

 

I too, am having snapped screw issues. My first box of 100 zinc screws, 7 of them snapped. Drill clutch is set quite light, the wood is not splitting or cracking, and the heads aren't seating/joint isn't pulled together. I"m hoping its just a bad batch - but its something worth keeping an eye on.

And I will add that Kreg, to their credit, has offered to send me a replacement box - I'm not looking for free product though (not that I object to free... but its not the point) - more simply chiming in that... with more than a couple people having snapped the zinc plated screws - I've found a few posts around the net on that, now that I'm looking - it might be something Kreg might want to followup and test around. I'm going to be watching my next few boxes.  For Kreg, since they are watching - I do have the box still - would there be a SKU or tracking number on it that would give you any lot/mfg info you might need?

Just a notion I wonder if the bronze screw were passivated thus allowing them to drive in easier? Using the steel screws wipe the screw across a candle to ease screwing and stop the screw possibly heating and thus snapping, tedious I know better than ruining the job because broken screws are near impossible to remove

I'm planning on building several projects using my Kreg Jig this year. I've also noticed a few negative posts about the new screws on various woodworking sites over the past year. I'm just wondering if there really was any serious issues with these screws and if so have any changes been made to correct them?

Trevor,

When installing screws in hardwoods, I always lube the screws---

screw-lube, bees wax or parafin.

The lubrication reduces the risk of breakage.

I don't have any problems with screws breaking---including the zinc plated screws.

Also, I  make it a practice to lube long threaded screws, for deep thread engagement, including softwoods, such as pine.

PS---drive the screw half-way in---reverse the screw and install it 'til it bottoms out.

This process removes any wood fibers, than accumulate in the root of the screw, causing binding.

This is especially necessary when installing screws in thin sections.

 

When the screw enters the wood, between the growth rings, it has a tendency to spread the wood apart---

hence the reason for this proceedure.

NOTE:  DO NOT install a screw into the end-grain.

If you must, install a dowel in the work-piece and install the screw into the dowel.

When drilling pilot holes into wood, its necessary to select the proper drill-bit diameter.

The drill-bit dia should be equal to the screws minor (root) diameter.

The intent is for the screw threads to grip into the wood.

You don't want the shank dia to spread the wood apart---else the wood is subjected to fracture.

PS---a small dia screws, a little sliva will suffice, on the leading end of the screws.

I've made several projects and made repairs, using small #2 & #4 screws.



Trevor stafford said:

Just a notion I wonder if the bronze screw were passivated thus allowing them to drive in easier? Using the steel screws wipe the screw across a candle to ease screwing and stop the screw possibly heating and thus snapping, tedious I know better than ruining the job because broken screws are near impossible to remove

Rich,

Many of the negative posts aren't justified.

There are many out there who find something to complain about.

There's many who don't know the proper technique or process for using and installing screws.

Some haven't learned. 

Screws are designed for their intended purpose, and when properly used, there's not a problem.

I've seen people putting machine screws into wood and have complained about the screws not holding.

They are clueless.


Richard Ljungquist said:

I'm planning on building several projects using my Kreg Jig this year. I've also noticed a few negative posts about the new screws on various woodworking sites over the past year. I'm just wondering if there really was any serious issues with these screws and if so have any changes been made to correct them?

Thanks for the input Ken.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_