Kreg Owners' Community

My kreg drill bit is burning the wood (and not cutting) when I try to drill the pocket holes. Any recommendations? I want to build solid oak slabs by joining on the flat.

Views: 532

Reply to This

Replies to This Discussion

Drea,

My first impression, of the wood burning, is that the drill bit is dull.

Resharpen the bit or try a new one.

How would I go about sharpening the bit? (Sorry to be such a newb).

Ken Darga said:

Drea,

My first impression, of the wood burning, is that the drill bit is dull.

Resharpen the bit or try a new one.

You'll need some diamond sharpening steel tools.

Files, in the shapes and sizes to accommodate the cutting edges on the bit.

If you don't have the proper tools or know how to sharpen drill bits,

I'd suggest just buying a new drill bit.

The sharpness of a drill bit, can be examined by using a magnifier, and preferably under a bright light.

Look closely at the cutting edges, of the drill bit.

If any shiny spots (''white caps'') are visible, the cutting tool needs sharpening, so as to result in a smooth cut.  

  Contact Kreg Customer Service---they may offer a sharpening service.

  Another point---

when drilling pocket holes, one needs to raise the drill bit often, so as to remove the wood chips and shavings.

Drill about 1/4'' deep at a time---

Raise the drill bit---

remove the shavings---

repeat---

until the bushing on the drill bit touches the drill guide block.

(Raise the drill bit, to a height so as to allow the drill bit flutes to expel the chips/shavings.

  Drill speed of 2000 - 2500rpm, is recommended.

  Allow the drill bit to do the work.

Apply moderate pressure, while drilling---

DO NOT apply excessive force.

(If ‘’squeaking’’ of the drill bit is experienced, a suitable lube can be applied to the drill bit cutting ends, flutes and ‘’drill stop’’ face, that makes contact with the drill guide block).

  The wood chips/shavings need to be removed, during the drilling process.

NOTE:  When the woods chips/shavings are not removed during the drilling process, the interference of the woods chips in the hole, will not allow smooth cutting--- excess heat produced by the spinning drill bit, will over-heat the wood chips and cause a burning effect, and not allow the drill bit to drill a satisfactory clean and smooth hole.

  An alternate, to as described above, a vacuum can be used, to extract the wood chips thru the accessory the port, on the drill guide block.  

This feature is great---it saves lots of time, when the set-up is at a drilling station, when drilling lots of holes.

  When one is drilling only a few holes, and the drill guide block is not fitted into the drill guide block housing/support, then use the method, as described above.

Also, one can blow away some the wood chips, by the ‘ol wood workers method---“ use your mouth’’, akin to whistling, while you work.

I find that adding my dust collection unit to the dust collecting port that came with the jig works great, I don't have to go up and down when drilling as the dust collector is sucking up all the chips.

Check out this page, it tells how to have Kreg sharpen your bit, I don't recall what the cost it, but it wasn't bad, I think all you'd be out is shipping fees...and the results would be far superior that doing it by hand.

http://kregjig.ning.com/profiles/blogs/drill-bit-sharpening-service

There are skilled craftsmen, that visit this forum, that can put a keen edge, ''hand sharpening'' a drill bit.

So---how can you say, ''...the results would be far superior than doing it by hand.''

darwincam said:

>>>> ...and the results would be far superior that doing it by hand./p>

 

Not say'n anything about skills and abilities of people here, but you have to admit there is a VAST range of skills and abilities that vist this forum, and some have the skills some don't.  I merely pointed the OP to the bit exchange service offered by Kreg.  By the time one purchases the diamond fies they'd own many new bits.  For the average Joe, in my opinion they will not have results as good as a replacement bit from Kreg.  If you want to spend your time sharpening the bit by hand Ken, knock yourself out.  For me, it doesn't even make it to the consideration phase.  YMMV.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_