Kreg Owners' Community

 

 

Introducing the Kreg Rip-Cut™


Available at Kreg Dealers everywhere

$34.99


Ripping down large panels into smaller more manageable workpieces can be one of the trickiest, most intimidating, and expensive steps of any wood project. Even for experienced woodworkers ripping with the nicest table saws, you’re still forced to lift large heavy panels, balance them carefully to avoid binding and bowing, while at the same time trying to support the finished workpieces  and waste material as they exit the saw.

 

There is a faster way. There is an easier way! There is a better way.

Introducing the Kreg Rip-Cut™.

 

The Rip-Cut™ is an incredibly handy tool which speeds and simplifies the process of ripping down large plywood and MDF panels. No more taking your work to the saw, instead take the saw to your work. No measuring, no marking, no chalk lines – the Rip-Cut™ quickly and easily attaches to almost any circular saw, letting you cut pieces up to 24” wide with tremendous accuracy.

 

The Rip-Cut™ is a no-nonsense, straight forward, precision accessory for your circular saw that is so incredibly affordable it will pay for itself in no-time. It features a durable design including a solid aluminum guide rail, ultra-durable impact resistant plastic, an easy-to-read precision adjustable scale, and a reversible guide arm which works whether you’re left or right handed. It’s a super easy, precise, and affordable way to break down large panels for almost any project.

 

  • Connects to almost any circular saw – right or left blade
  • Reversible Guide Arm for Right or Left Hand Use
  • Makes rip cuts up to 24” wide
  • Rip sheets of plywood in half – in just one cut
  • No measuring, marking, and no chalk lines
  • 100% Guide support through entire cut
  • No need to remove Rip-Cut™ when doing cross cuts
  • Quick and accurate adjustments – no tools required
  • Lightweight/Sturdy Design for use on the jobsite

 

Materials:
High Quality Aircraft Aluminum
Impact Resistant Plastic Polymer

Aluminum Guide Rail:
3" wide x 30" long
 

Saw Sled

6 1/2" x 8 1/2" saw platform

Guide Arm:
2" wide x 10" long
Minimum 5" edge bearing at blade entry
Minimum 3" edge bearing at blade exit
 
Cut Width:
Maximum 24"

 

Check out the Rip-Cut on www.kregtool.com!

http://www.kregtool.com/RipCut-Prodview.html

 

 

 

 

 

Views: 51423

Reply to This

Replies to This Discussion

Does this work with right angle saws?  Only sidewinders are shown.

I think this would be WAY faster than clamping a straight edge and ripping, and the price point seems easy enough....thanks KREG!

I want to see the same exact thing. Thanks for mentioning it.



Kamil Czuba said:

Is there a video of actual use?  All the pictures show the saw half way through the panel.  I'd like to see one at the start of the panel, as only 1-2" of the guide piece will be touching the side of the panel.  Not very stable.

Dear Kreg,

 

I have been wanting a product that will help me precisely cut panels the exact same size time after time with a price tag that I can afford.  As some have pointed out there are a few vendors that have a really good track system with arms that can do this.  I'm fortunate enough to own their plunge saw and guides but unfortunaltey cost is an issue for me in regards to their parellel arms that helps me cut exact same size panels.

 

I love the concept but the main reason people use a table saw or a track saw system is to rip large panels wihtout having all the tearout.  This is the whole reason for such precise panels such as building cabinet carcasses. Not sure that this solves that problem.  Not sure about others but Im not usually ripping large panels unless I'm building furniture and if I need to rip panels for say something like siding for a shed, then usually such precision is not an issue.

I love and own many Kreg tools but this one is probably still not going to work for me :-(

 

Mark

 

 

 

Great new product.  I don't have room to take a table saw on a trip.  But I need a good way to rip 4 X 8 sheets.

What happened to inovation???

A few years ago I visited the local aluminium door maker, Took a look at their rack of profiles, bought a 3m length of one a 2m length of another and a 1m length of a third, added a few bits of 3mm MDF and I have 2ft, 4ft 6ft and 8ft options with a carriage for each saw, the jigsaw (It doubles as a circle jig) and both routers - all for at total cost of less than £20.00 and it's as rigid as heck!!!

Sorry Kreg. this one's a loser!!!

In theory it looks like a good tool but I can see it binding on long , wide cuts. There are several other 50-100 inch straight edge clamps out there that will do the job. I made a wood jig to match the saw offset which eliminates the measuring with such clamps.

Is there a metric measurement available? 

In my honest opinion, the "blue" piece that rides along the edge of the wood SHOULD  be of equal length on both sides of the Aluminum. More like a drywall "T" square to give you more stability when starting and ending your cuts!!

 

John

I have same reservations about start of cut & ease of setup. Also I wonder about cuts at the far end of its maximum length. I think there may be a bit of wobble as the edge guide would be a fair distance away and you would need to hold the guide against that edge with your spare hand to prevent any wobble. 

This look like it has potential. I see one major flaw in the design in its current form though... Kreg, will you release a metric version or at least have a conversion kit available for it? Imperial measurements are fine should you want to limit your sales to the US alone, but here in Australia and over in Europe, feet and inches went out the window over 40 years ago!!!

Looks good, can't wait to get mine.

 

It seems to have the same limitations present in my old Accurip saw guide--24" capacity. This is fine for many jobs, and if you can't find that other saw guide, this Kreg version looks OK. If Kreg brings its typical attention to detail and usability, it may very well be worth the premium price. In use, I have not had any problems with binding with the Accurip, but it doesn't have the precision offered by a track saw. Since it uses the edge of the sheet as the reference edge, your cut isn't going to be any better than that. I recognize that a circular saw isn't going to serve as anything but a tool to hack big sheets into pieces small enough to manage on precision equipment, no matter what accessories one attaches to it.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_