Tags:
Is there any detriment to alternating.....
I've done a few round table top edge joining and I alternate the screws from one side to the other. It just seems like you would get a stronger joint because the stress would be more spread out, if that makes sense. I don't use glue. I guess some kind of a test would have to be made to get true results.
I have a friend locally that puts the screws all on one side. So I guess either way works.
My table tops are a couple years old now, and are still flat, smooth and true.
Jim, I have used both methods and I really don't know if alternating the sides adds any benefit, logically I would think it would but I have no data to support my thought.
I do have another edge joining technique question for anyone. A while back someone posted a discussion on the technique they use to join angle cut edges (such as used on a half moon top to a treasure chest), I am struggling finding that posting and if anyone remembers it or knows how I can find it I would appreciate some advice.
Don,
Is Angled Joints/Curves at pp. 27 -28 of the K3 Manual http://www.rockler.com/tech/RTD10000075AC.pdf
of any help?
Don Hays said:
[snip]
I do have another edge joining technique question for anyone. A while back someone posted a discussion on the technique they use to join angle cut edges (such as used on a half moon top to a treasure chest), I am struggling finding that posting and if anyone remembers it or knows how I can find it I would appreciate some advice.
Richard,
Thanks for the link, I had not seen this before. I plan on giving this a try in the next couple weeks.
Don
Don,
Hope that info helps. Show us the result when it's finished.
Richard
I guess I have a similar edge-joing question...similar to what's covered in the reference above:
Angled Joints/Curves at pp. 27 -28 of the K3 Manual http://www.rockler.com/tech/RTD10000075AC.pdf thanks to Richard. If I am trying to join that wood triangle, what they're calling the gusset, made of 1" pine and maybe 3" on each side, is there some way of setting up the jig so as to drill the pocket hole directly into the hypotenuse edge, at right angles, so that a screw would go into each piece to be joined by the gusset? I guess it's almost the same as in the diagram in the manual, but instead of drilling the pocket hole into the side of the gusset, I'm thinking of drilling the hole straight into the edge of the gusset...Thanks for any suggestions.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service