Tags:
I have a 50" high space, a 42" long (not counting the metal frame) over the door ironing board and would like to use it at a 36' height. Do you have any suggestions for mounting it in a cabinet like this? Thank you for your thoughts.
Lana,
In my reply above (nov 2, 2010) I attached a pdf file with the dimension, cutting guide, etc. Remove the ironing board from it's metal frame and adjust the size of the cabinet to fit the board and to the available space. From your info it sounds like you have room but it may not be exactly at 36" height. Provide some detailed dimensions of the board and I'll be glad to make recommendations.
My Dad built one of these when I was a kid and it had a standard size ironing board made of wood, hinged to the bottom of the cabinet with a leg that swung down to support the weight when in use. The board, pad, cover and leg all fit back neatly into the cabinet. I don't remember any shelves though.
sorry but i am not sure what is holding the board above the floor.a set of hinges will just pull out if they are by themselves.our old wall iron board had legs that folded down to the floor to make it stable.also make sure you fasten your unit into the 2x4 studs or you will have your sheetrock and the box on the floor.
the best one we had as kids was right in the wall,between the studs,it never came loose.that one had a T looking board that came out with the iron board and fitted in a cut out on the end.
the one you did just got me thing about making another one in this house.the wife and i hate getting the metal one out of the closet and then putting it back away everytime you need to iron.if we leave it up then i hate it even more when it is in my way to the books.
Outsider: this project is only the cabinet for the hide-a-way ironing board. You are correct, most hide-aways do have some sort of support that usually folds up under the board. This one is attached between the studs from which the wall board is cut out of, it's not attached to the wall board.
I wish I was a carpenter and could explain well what was built for us, because I just love it!
The board is plywood and is shorter because it swings up from the floor at the exact working height. There is a hinge as long as the ironing board is wide that attaches to a board that goes across the cupboard, near the top and fairly close to the front, the back edge of the ironing board sits on this board when it is open. There is an angled support (4x1?) attached to the underside of the ironing board near the front, that is cut and hinged in the middle, with the middle folding up and laying against the back of the cupboard when closed. There is also a long hinge, like you might use to hold the lid of a toy box open that attaches from the underside of the ironing board down to the angled support, it makes it very sturdy when in use. He put a piece of plywood on the back wall and built on to it a little frame at the floor that make a track to hold the other end of the angled support. The angled support just rests in it- it isn't nailed down or hinged. The track is made of 2 vertical 'sides' app 12" tall and are attached at the floor to the back wall with enough space between them for the angled ironing board support to slide freely between them and then underneath the angled support is the 'front' of this frame that goes from the floor up maybe 6". To keep the angled support from jumping out of the track made by this little frame he put a piece of plywood that fits under the angle ironing board support but sticks out 1-2" beyond the frame. It isn't hinged or nailed down and seems to act as a pivot and a guide to keep it inside the track made by this frame. Sorry if this doesn't have clarity to match the enthusiasm!
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service