Kreg Owners' Community

Hello, I just purchased my Kreg Jig. Can some of you experienced users tell me how you mounted your jig? Did you mount it to a bench? Or a piece of plywood or something and then clamp that to a bench? Or is there a better way for storage, mounting and using the jig?

Thanks

Views: 20142

Reply to This

Replies to This Discussion

Yes, they are the "support wings" which were part of the K2000 Propack several years ago. I believe they are now discontinued and I am not sure the height would work with the newer Kreg jigs. On of their best features is that they have a built in "gauge" for setting the stop collar on the drill bit.

Mark Alward said:
"I mounted mine on a bit 3/4" plywood. Here's a picture of it hanging on the wall. Actually it is sitting on a rail, and retained by a cleat and the Kreg clamps around the conduit. If you look closely you will see a drill bit and driver bit stored there as well (in two of the guide bushings of the jig). Not too purty but it works and keeps everthing together. Often I just sit it on the bench, unless working with large workpieces it is not necessary to even clamp it "

Are the blue blocks a Kreg option/accessory? I assume they are the same height has the Jig..

AWK
Rex, I opted to mount my Kreg jig and give it its own dedicated space. I knew that if I had to fool with setting it up over and over I would never use it. But one bit of advice I found before I did this has made such a difference. I read somewhere to set up the jig at just under waist height. This saves the back and shoulders when using it repeatedly. (which I do!). Drilling downward over and over has not been a problem. Before I built this table from scrap lumber I made a very short pair of sawhorses. LOL
Here is a picture. Yes, it is very low... I am only 5'2"
I also had an old drill that I use just for this. Now I never have to remember to charge the battery and it is there ready to go!

I got tired of taking it out of the gray box and putting it back all the time. Plus, in my shop, I don't have a lot of room to clamp it down quickly. I ended up using scrap 3/4" board and screwed the Kreg Jig to it. I then drilled a somewhat large hole in the board and now just hang it up when I'm finished. Clamping the board it's screwed to is much quicker than just the one clamp to the half circle indent in the front of the jig.
Very nice. Now I need to find room!

Kim C said:
Rex, I opted to mount my Kreg jig and give it its own dedicated space. I knew that if I had to fool with setting it up over and over I would never use it. But one bit of advice I found before I did this has made such a difference. I read somewhere to set up the jig at just under waist height. This saves the back and shoulders when using it repeatedly. (which I do!). Drilling downward over and over has not been a problem. Before I built this table from scrap lumber I made a very short pair of sawhorses. LOL
Here is a picture. Yes, it is very low... I am only 5'2"
I also had an old drill that I use just for this. Now I never have to remember to charge the battery and it is there ready to go!

I keep mine in a portable stage so I just grab my work board and go

1st picture is on portable board.
3rd is Where the riser board allows to use as a clam down
4th Is where I make dowel rod plugs Just have screw in bootm of hole put dowell rod in and trim off with a pull saw and then knock out the screw and plug comes out
Attachments:
I mounted my jig to a piece of pine board and then drilled two holes at the top of the board and into my work station (which by the way measures 4'x4'). Now I just lay my jig on my work station and drop in 2 carriage bolts to hold it in place and I am good to go.
Jens Jensen said:
I keep mine in a portable stage so I just grab my work board and go

Looks like a great setup, Jens! I'd like to see a video or some more photos of your dowel solution... looks like it should do the job. Thanks for sharing!
I mounted my jig on a 18" stair runner with two supports on each end of stair runner. It's heavy so it's stable and when working on long material I have two added supports to match height.
KregRep said:
Jens Jensen said:
I keep mine in a portable stage so I just grab my work board and go

Looks like a great setup, Jens! I'd like to see a video or some more photos of your dowel solution... looks like it should do the job. Thanks for sharing!
I just used drywall screws 1-1/4"and screwed it down to a piece of scrap plywood I use as a working surface and began to get to work.
Just discovered Kreg Jig before Chrismas and after a couple of temporary homes, I've settled on this - the Jig board stands on edge for a small storage footprint, and the table top comes off, the suports fold and it slides away too.



Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_