At Kreg, our position has always been that glue is completely optional - which stands in stark contrast with other wood joinery techniques. However, we also suggest that if you want the strongest joint possible, adding glue is the way to go. The great news is that if you do use glue, there's no need for hours of clamp-ups since the screws act as mini internal clamps while the glue dries.
Inquiring minds want to know... when you're building your own projects with Kreg Joints:
Tags:
I use glue when I know that the piece is to be permanent.
sometimes I remove the screws for cutting or just to save screws.
Some of the time. It always depends on the type and size of the project or - in some instances - how lazy I am at the moment or how much time I have to make the item. I think common sense is the best approach.
I apply Gorilla Wood Glue with a brush on all Greg joints for added strength. As you said the Kreg screws act as mini internal clamps while the glue dries and the bond is complete.
always, as not even the Kreg can hold as strong alone
One can minimize the glue escaping, by spreading the glue into a thin layer, using an acid brush.
Apply a small bead along the center of the intended joint, spread it out evenly, using the acid brush---
keep the glue a short distance from the edge of the joint.
Remove any glue, that may ooze out, with a wet rag or towel, before the glue starts to set.
A scraper tool is also handy, lightly scraping the finished side, of the work piece.
Works for me.
Keeping joints and/or edges from slipping.
Insert a small brad, into the wood surface, leaving a portion of the brad, protruding above the surface.
Cut of the protruding brad, using side cutters. Side cutters which will leave a short section of the brad exposed---1/32 to 1/16".
Place the surfaces together, press into place, so the surfaces mate, and clamp in place while the glue is setting.
The cut points, on the brad, will penetrate into the adjoining surface and prevent slippage, during gluing/clamping.
Works for me.
Keeping joints and/or edges from slipping.
Insert a small brad, into the wood surface, leaving a portion of the brad, protruding above the surface.
Cut of the protruding brad, using side cutters. Side cutters which will leave a short section of the brad exposed---1/32 to 1/16".
Place the surfaces together, press into place, so the surfaces mate, and clamp in place while the glue is setting.
The cut points, on the brad, will penetrate into the adjoining surface and prevent slippage, during gluing/clamping.
Works for me.
You're welcome Steve.
My mission on earth is not complete,
I'm still here.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service