Sort by:
How to cut a 4 x 8 sheet of plywood perfectly using a Bora edge clamp, 2 saw horses, 2 Ridgid suppo… Tags: cut 4x8 plywood, Cutting Plywood Hal Schmidt "Woodmeister" Apr 22, 2014 1425 views
This is the third part of a three part video on refinishing a 100 year old solid oak secretary desk…
Tags: antique, refinishing
Hal Schmidt "Woodmeister"
Dec 28, 2011
243 views
This is the second part of a three part video on refinishing a 100 year old solid oak secretary des…
Tags: antique, refinishing
Hal Schmidt "Woodmeister"
Dec 24, 2011
234 views
This Part I of a multiple part video on refurbishing antique furniture. Hal the "Woodmeister" is re…
Tags: antique, refinishing
Hal Schmidt "Woodmeister"
Dec 21, 2011
261 views
How to cut a piece of 4x8 plywood with a skill saw, It must be supported properly and the use of gu…
Tags: cutting plywood, Woodworking
Hal Schmidt "Woodmeister"
Dec 18, 2011
2277 views
If you want to make cement counter top, you should make samples to be sure you like it; other wise…
Tags: cement, counter top
Hal Schmidt "Woodmeister"
Dec 30, 2010
364 views
The parts of the cabinet are coming together. This is part 8 in making a cabinet for my "Man Cave"…
Tags: Hal, door
Hal Schmidt "Woodmeister"
Dec 15, 2010
420 views
This is the 7th in series on building a corner cabinet for my "Man Cave" The first is "Hal Messes w…
Tags: Hal, joiner
Hal Schmidt "Woodmeister"
Dec 15, 2010
368 views
This is the 6th in a series on making a corner kitchen cabinet that is going into my "Man Cave"
Tags: stile, rail
Hal Schmidt "Woodmeister"
Dec 13, 2010
308 views
I am adding a faceplate from material that was planed in the previous video. This video is the 5th…
Hal Schmidt "Woodmeister"
Dec 8, 2010
240 views
Taking walnut from a lumber mill and turning it into parts to finish off my corner cabinet which is…
Tags: Hal, planing
Hal Schmidt "Woodmeister"
Dec 6, 2010
308 views
This is the third in a series on building a corner cabinet. The first is "Hal messes with Kreg" and…
Tags: Hal, kreg
Hal Schmidt "Woodmeister"
Dec 4, 2010
210 views
This a progress report on making a corner cabinet. The start of the project is in a video call "Hal…
Tags: corner cabinet
Hal Schmidt "Woodmeister"
Dec 3, 2010
216 views
This is a video on how to cut plywood correctly using a saw guide and proper supports.
Tags: saw guide, plywood
Hal Schmidt "Woodmeister"
Dec 2, 2010
900 views
Hal in his shop making a Cabinet frame using a Kreg tool. This is the first stage of making corner…
Hal Schmidt "Woodmeister"
Nov 27, 2010
237 views
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I have had the ACS for about a year. Was wondering if there any other blades, like a Diablo, that will fit the saw?Continue
Started by Randall H Gress in Beginners' Zone Feb 20.
I have been using the Automaxx 6" clamp for two plus years, and recently the clamp is impossible to close the handles to secure the work and my jig. I cannot close the handles no matter how much pressure I can exert. I open the clamp to max to reset…Continue
Tags: clamp, inch, 6, Automaxx
Started by Anthony M Calabrese in Other Kreg® Products Feb 12.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 4 Comments
© 2021 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service