Kreg Owners' Community

michael dunn
  • Plainfield, IL
  • United States
Share on Facebook
Share

Michael dunn's Friends

  • Dick Pattillo
 

michael dunn's Page

Latest Activity

michael dunn replied to brian lazenby's discussion 'Edge Joining 2" Boards'
"Essentially when all is said and done it is the glued up joint that is the main event while the screws initially act as an “in place clamp” while the glue sets up. Purchase good quality glue such as titebondIII and utilize proper…"
Dec 15, 2018
michael dunn commented on Daniel espinosa's photo
Thumbnail

01ea447cb616c44229872fcd8554fec58b5f045afa

"Nice looking cabinet Daniel"
Dec 15, 2018

Profile Information

Which Kreg products do you own?
Kreg Jig K4/K4MS, Cabinet Hardware Jig, Kreg Screws, Pocket-Hole Plugs, System Organizer, Right Angle Clamp, Face Clamps
How would you describe yourself?
Intermediate Woodworker
How did you learn about the Kreg Owners' Community?
kregtool.com, Kreg YouTube, From a Friend
What's one interesting fact about you, your life, your garage, shop, or home?
enjoy motoring around USA on my Harley Davidson

Comment Wall (4 comments)

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

At 5:30pm on November 16, 2014, Dick Pattillo said…

Thanks for the nice complement Michael, but I didn't really have a plan as such.  I just built four cases that would all fit together in the space I had to work with.

Thanks again,

Dick

At 8:20pm on March 13, 2014, Eddie Harrel said…

Hello Mike, my cut list was 1-1x8 71inches, 1-1x4 71 inches, 1-1x4 80 inches for the top cap, 12-1x2 17 3/4 inches for slats, 1-1x4 17 3/4 inches for middle slat (The slats are spaced 3 and a half inches apart).  I centered the middle slat then used a piece of 1x4 as a spacer.  2-1x4 48 inches as the end posts.  I used a 1/2 inch round over router bit to round over edges.  Hope this helps.  I did not make a foot board.  Thanks Eddie

At 7:36pm on March 13, 2014, Eddie Harrel said…

Hello Mike,  Not sure what your last post said at the end but will share any info I have on my projects.  Thanks Eddie

At 5:12pm on March 13, 2014, Eddie Harrel said…

The end post are 1x4's 48inches tall.  Thanks

 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

New to K5 and pocket holes, any video’s on the materials listed below?

I am using Danny Proulx book on shop workstations. I am deciding whether to use MDF or Melamine. He calls for MDF. However; I like the looks of the melamine.  I am a little leery of using pocket holes for it. One of the main reasons is I have no…Continue

Started by Michael Lusk in Beginners' Zone yesterday.

Adaptive Cutting System T-Track Stops Mod 1 Reply

I bought the ACS a couple of weeks ago & have been pleased with the results on my first small project (LP record crates)... I was disappointed with the plastic accessories for the table-top, especially the T-Track stops. I'm pretty sure they…Continue

Started by John Moore in Beginners' Zone. Last reply by Deac Manross May 17.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_