-
Pierre Vallee
- Male
- Victoria, British Columbia
- Canada
- Product Reviews
- Discussions (59)
- Photos (50)
- Projects (12)
- Videos
Pierre Vallee's Discussions
Kreg circular screw selection guide
25 Replies
Saw a Kreg circular screw selection guide at a local distributor with the tool box. I would like to know where to aquire the guide and how much? Thanks. P. ValleeContinue
Started this discussion. Last reply by Pierre Vallee Mar 5, 2013.
patio / garden planter with telescopic legs
16 Replies
Looking for idea on extendible / telescopic wooden legs for a planter box. Square tube type with insert perhaps to permit raising or lowering the planter box. Would like to make them out of wood with…Continue
Started this discussion. Last reply by Pierre Vallee Jul 4, 2012.
doos and don't of the mighty jig
7 Replies
OKreg! I use to do pocket holes by measuring carefully and then back-drilling from the end in the stock at about 5 to 10 degrees. Of course I didn’t have a pocket shoulder to drill up against unless…Continue
Started this discussion. Last reply by Ken Darga Jun 18, 2012.
avoid splitting when driving pocket hole screws along the grain into an end piece...
2 Replies
Even when selecting the correct setting and drill bit measurement, and screw length and type, have experience some splitting or crunching in the wood at the end of a piece. This occurs when pocket…Continue
Started this discussion. Last reply by Pierre Vallee May 11, 2012.
Pierre Vallee's Page
Profile Information
- Which Kreg products do you own?
- Kreg Jig® Master System
- How would you describe yourself?
- Moderate Woodworker
- What's one interesting fact about you, your life, your garage, shop, or home?
- retired electrical engineer and keen woodworker now. Big fan of cool 2x4 ideas and pocket drill holes (been doing them by 'back-drilling' at first before assembly, if you get my drift ;-)
pv
just purchased the Master System, can't wait to try it... arrrr arrr!
Pierre Vallee's Photos
Need Help?
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
Popular Posts & Projects
Videos
Forum
Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
40mm Cup Hinge Jig Question
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
Product Reviews
New Kreg 720Pro
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Not Pleased With Pocket Hole Construction
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
Comment Wall (1 comment)
You need to be a member of Kreg Owners' Community to add comments!
Join Kreg Owners' Community
holy moly! that is a lot of work. I see that you had to groove the outside ring and notch the narrow end of the spokes. A little splitting occured huh? I wonder: I assume that you pre-dilled? would the wider end of the spokes be ok with two pocket holes, glue and no groove? Anyway, a great job for a first! how would you modify the design for the next one?