Kreg Owners' Community

Matthew Hinton
  • Mobile, AL
  • United States
Share on Facebook
Share

Matthew Hinton's Discussions

Is my drill speed set too high when screwing?
5 Replies

I was building the workbench from the Kreg plans.  I used treated yellow pine as it was going to be outside. I'm trying to understand why the screws poked through sometimes in the picture?I checked…Continue

Started this discussion. Last reply by Glen S Jan 28, 2018.

Need advice on building an interior door
3 Replies

I was trying to design a interior passage door for our laundry room.  Dimensions: Thickness is 1 and 3/8". Width is 32".  Height is 79".   I've attached a rough sketch.  I was thinking of building…Continue

Started this discussion. Last reply by Ken Darga Feb 21, 2017.

Ana White daybed build question
6 Replies

I'm reading over the daybed plans listed here.…Continue

Tags: white, ana, daybed

Started this discussion. Last reply by Ronda McElroy May 6, 2016.

Questions after making a bookshelf
2 Replies

I built the bookshelf in the attached picture.  Dimensions are as follows.  I used 1x 12's with 1/4 in sandeply backing.  Sides are 29 in tall.  Horizontal shelves are 36 inches across.   I made best…Continue

Tags: bookshelf

Started this discussion. Last reply by Matthew Hinton Feb 19, 2016.

 

Matthew Hinton's Page

Latest Activity

Glen S replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"I'm certainly glad it all worked out for you in the end. You may have been into some softer wood on the other joint too. Either way you've got a nice bench that is ready to work for you. Nicely done."
Jan 28, 2018
Matthew Hinton replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"Hi Glen, The plans I was using were the workbench plans that used to come with the Kreg K4.  They called for 2 1/2 screws.  I see you point about the screw length.  However, the screws are going in at an angle.  I think…"
Jan 27, 2018
Glen S replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"The 2 1/2" screws seem too long for attaching to the face of a 2x4. I would think that direction would only take a 2'' screw because the 2x4 is really 1 1/2" in that direction. 1 1/2" of wood plus the 1/2" (??)of…"
Jan 23, 2018
Matthew Hinton replied to Bigchief's discussion 'Full size bed'
"Hello... As for plans, there's quite a few websites in addition to Build Something.  Please see the below discussion thread. HTH! https://kregjig.ning.com/forum/topics/good-wood-working-plans-site"
Jan 23, 2018
Matthew Hinton replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"Hi Dan, It does now that I think about it.  "Wet wood" is very possible. We had a light dusting of snow here earlier in the week.  I had a tarp over the wood. I noticed it was still somewhat damp when I pulled the cover off.…"
Jan 23, 2018
Dan Duce replied to Matthew Hinton's discussion 'Is my drill speed set too high when screwing?'
"Hi Matthew, Based on my experiences I'd say there are a few possible culprits. 1. Wood is wet and soft.   - I've noticed screws will dig deeper through pine, especially if it is fresh 2. Drill clutch setting / speed is too…"
Jan 22, 2018
Matthew Hinton posted a discussion

Is my drill speed set too high when screwing?

I was building the workbench from the Kreg plans.  I used treated yellow pine as it was going to be outside. I'm trying to understand why the screws poked through sometimes in the picture?I checked that the settings on the Jig were correct.I used 2 1/2 in Kreg screws to join the 2x4's.The wood was dampI had my cordless drill set to half-speed.  This drilled the screw holes fine.After seeing the screw poke through, I turned the setting down.When screwing, I do want to make a stout connection.  I…See More
Jan 21, 2018

Profile Information

Which Kreg products do you own?
Kreg Jig K4
How would you describe yourself?
Beginner DIYer
How did you learn about the Kreg Owners' Community?
Internet Search
What's one interesting fact about you, your life, your garage, shop, or home?
I'm a member of the the Mobile Makerspace. While there's many intrests there, one is woodworking. If you are ever in Mobile, Ala, feel free to stop by.

http://makerspacemobile.org/

Matthew Hinton's Photos

  • Add Photos
  • View All

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-cut

Looking at buying the Kreg Accu-Cut and am interested in hearing feedback.Thanks.StanContinue

Started by Stanley C. Pearse in Beginners' Zone Jul 1.

Wheelbarrow organization 2 Replies

Anybody have any ideas on how to make a couple wooden attachments for the side of a wheelbarrow that can hold and secure some long handle yard tools?

Started by Vincent A Cutright in Beginners' Zone. Last reply by Vincent A Cutright Jul 6.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_