Kreg Owners' Community

Mike R
  • NY, NY
  • United States
Share on Facebook
Share on Facebook MySpace

Mike R's Discussions

Kreg Foreman 210 and Plywood

What is the correct setting when using 23/32 plywood?I am using the Foreman for plywood that is 23/32 and not 3/4".I put the fence on the 3/4" mark where the back of the fence lines up with the back…Continue

Started Jul 5, 2020

Cabinet with Pocket Screws
2 Replies

Hi.  My son and I am building some cabinets to hold some band instruments for the local school (an Eagle Scout project).  We are using 3/4" baltic birch plywood (60" x 60" pieces) and Kreg pocket…Continue

Started this discussion. Last reply by Mike R Jun 13, 2020.

Adaptive Cutting System Saw Calibration
3 Replies

Hi.  I just go the Adaptive Cutting System and setting it up.  This is my first track saw.On saw calibration, the Kreg video says it "should" be calibrated.  Mine is not.  Just curious if anyone else…Continue

Started this discussion. Last reply by Mike R Mar 23, 2020.

 

Mike R's Page

Latest Activity

Mike R posted a discussion

Kreg Foreman 210 and Plywood

What is the correct setting when using 23/32 plywood?I am using the Foreman for plywood that is 23/32 and not 3/4".I put the fence on the 3/4" mark where the back of the fence lines up with the back of the 3/4" raised mark.I set the drill depth using the block and after setting it, the point of the bit looks 1/32 off the fence.I have not had screws poking through.  However, today I had one on a test piece I was doing.  It might be because I put it in at a bad angle.I want to confirm the right…See More
Jul 5, 2020
Mike R replied to Mike R's discussion 'Cabinet with Pocket Screws'
"I tried the kregtool.com/help and also emailed several times a few weeks ago and no response.  I will try and call."
Jun 13, 2020
KregRep replied to Mike R's discussion 'Cabinet with Pocket Screws'
"Hi Mike, Please contact our team at 800-447-8638 or kregtool.com/help - They will be happy to advise you with this. Thanks!"
Jun 12, 2020
Mike R posted a discussion

Cabinet with Pocket Screws

Hi.  My son and I am building some cabinets to hold some band instruments for the local school (an Eagle Scout project).  We are using 3/4" baltic birch plywood (60" x 60" pieces) and Kreg pocket screws (we have the DB210 foreman).  Here is a link to a drawing for the first of 6 cabinets. https://www.dropbox.com/s/u4cojaa3k92ag30/cabinet 5 - Pub.pdf?dl=0This…See More
Jun 10, 2020
Mike R replied to Mike R's discussion 'Adaptive Cutting System Saw Calibration'
"I contacted support and been going back and forth on calibration. I have the saw set up and the accuracy over 48" is 1/32" - One end of the 48" piece is 1/32" wider than the other.  I calibrated the track 3 times to see if…"
Mar 23, 2020
KregRep replied to Mike R's discussion 'Adaptive Cutting System Saw Calibration'
"Please contact our team at 800-447-8638 or kregtool.com/help - They will be happy to assist you with this. Thanks!"
Mar 23, 2020
Ken Darga replied to Mike R's discussion 'Adaptive Cutting System Saw Calibration'
"I'd suggest contacting Customer Service/Tech Support 800-447-8638"
Mar 16, 2020
Mike R posted a discussion

Adaptive Cutting System

Hi.  I just go the Adaptive Cutting System and setting it up.  This is my first track saw.On saw calibration, the Kreg video says it "should" be calibrated.  Mine is not.  Just curious if anyone else got one and if it was calibrated.For calibration, Out of the box, the dial is on -1.  If I move it to 0 and lock in with the bevel locks it is square.  I want to make sure I should get it to zero with the set screws on the bottom, then I adjust the the dial to zero after.is the -1 used when you…See More
Mar 16, 2020

Profile Information

Which Kreg products do you own?
Kreg Jig K3/K3MS, Foreman, Kreg Screws, Pocket-Hole Plugs, Wood Project Clamps, Right Angle Clamp
How would you describe yourself?
Beginner Woodworker
How did you learn about the Kreg Owners' Community?
Not Sure
What's one interesting fact about you, your life, your garage, shop, or home?
its a hobby

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_