Kreg Owners' Community

Jeff Fishman
  • Yorktown Heights, NY
  • United States
Share on Facebook
Share

Jeff Fishman's Discussions

Looking to build a wood box with mitered joints (Kreg Jig 4)
7 Replies

Hi FolksNewbie making his 2nd post.  I want to build some wood boxes using 3/4" wood. The box will be 8" high, and approximately 18" wide by 14" deep.I want the box to have mitered corners rather…Continue

Started this discussion. Last reply by Ken Darga Apr 20, 2017.

Kreg 4 jig Newbie - wood splitting problems
3 Replies

Hey folksI am an experienced carpenter and do some cabinetry. I just purchased the Kreg 4 jig.  I wanted to test the jig by building a simple box with some scrap 3/4" paint-grade plywood and 1 1/4"…Continue

Started this discussion. Last reply by Jeff Fishman Apr 20, 2017.

 

Jeff Fishman's Page

Latest Activity

Ken Darga replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"Jeff, Spine joinery may be the way to go, if you're going to store and tote rocks in the box you've described."
Apr 20, 2017
Jeff Fishman replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"The spline joint would definitely have more surface area than biscuits.     my experience with biscuits is that they are extremely strong joints.  I find it really easy to use the biscuit joiner - and it allows for slight bits of…"
Apr 20, 2017
Jeff Fishman replied to Jeff Fishman's discussion 'Kreg 4 jig Newbie - wood splitting problems'
"Jay Thanks This was a scrap project and I never use drywall for finished cabinetry projects.  I did not have any Kreg screws available so I used a coarse drywall 1 1/4" screw.  I use SPAX lumber screws or wood screws for cabinetry…"
Apr 20, 2017
Jay Boutwell replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"The easiest and strongest mitered box is one that is held together with glue and a full length spline,  These can be made using either a router table and a slotting bit and or a table saw with the blade set at 45 degrees passing the miter ends…"
Apr 20, 2017
Jay Boutwell replied to Jeff Fishman's discussion 'Kreg 4 jig Newbie - wood splitting problems'
"A person should never use sheet rock or dry wall screws on anything except to attach drywall to framing.  The Kreg jig uses a bit that drills a flat bottom hole with a pilot hole to guide the screws directions into the receiving wood…"
Apr 19, 2017
Rick Wilson replied to Jeff Fishman's discussion 'Kreg 4 jig Newbie - wood splitting problems'
"Jeff, The screws are most likely the problem.  Kreg joinery is designed to be done with Kreg screws.  I have used Kreg products for a number of years and had no problems if used as designed.  Get the Kreg screws and get the kreg…"
Apr 19, 2017
Jeff Fishman replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"Thanks Ken  :-) I have a biscuit joiner and often have used it for cabinet drawers.  I haven't done miters with biscuits but will play around with some scrap stuff this week Jeff"
Apr 19, 2017
Ken Darga replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"Jeff, With mitered corners, I use biscuit joinery--- no exposed screws. This gives it the best appearance."
Apr 18, 2017
Jeff Fishman replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
"As I suspected, I saw a comment stating that there may be too much material removed after making miter cut for pocket holed screws to get a good hold.   I'm going to play with some scrap wood this week in any case to see if smaller screws…"
Apr 18, 2017
R. E. Woods replied to Jeff Fishman's discussion 'Looking to build a wood box with mitered joints (Kreg Jig 4)'
Apr 18, 2017
Jeff Fishman posted discussions
Apr 18, 2017

Profile Information

Which Kreg products do you own?
Kreg Jig K4
How would you describe yourself?
Advanced DIYer
How did you learn about the Kreg Owners' Community?
kregtool.com
What's one interesting fact about you, your life, your garage, shop, or home?
My shop was once a wine cellar

Comment Wall

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

  • No comments yet!
 
 
 

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Wheelbarrow organization 1 Reply

Anybody have any ideas on how to make a couple wooden attachments for the side of a wheelbarrow that can hold and secure some long handle yard tools?

Started by Vincent A Cutright in Beginners' Zone. Last reply by KregRep 23 hours ago.

Constructing an island benchtop

G'day,I am a new member to the forum, although I have had the pocket jointer for a number of years, I just didn't get around to joining you.Anyhow - my wife and I are in the process of downsizing [in fact we are currently building our 3rd "Last…Continue

Started by Peter Watkins in General Woodworking Jun 19.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…

Continue

Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_