Kreg Owners' Community

Rating:
  • Currently 5/5 stars.

Views: 143

Comment

You need to be a member of Kreg Owners' Community to add comments!

Join Kreg Owners' Community

Comment by Hal Schmidt "Woodmeister" on December 24, 2010 at 1:35pm
Jens, the hinges on these doors are self closing, when you get them almost closed the pop tight to close.  The handles are not required because you can grab the door edge and open, but I like the looks of a good handle and they keep the door clean, now you have change for the 2 cents.
Comment by Jens Jensen on December 24, 2010 at 12:28pm

how about the magnetic closer and to open you push the door.They are used on stereo cabinets quite alot

 

Just my 2 cents

Comment by Hal Schmidt "Woodmeister" on December 24, 2010 at 9:00am
That is good idea, they are not hard to reverse.  I am going to wait until all the cabinets are done to install the knobs so I can be sure they have a balanced look and function correctly. Merry Christmas!
Comment by Al Barale on December 23, 2010 at 6:18pm

I don't know if this will help you now Hal but, You could have the doors all opening the same way," Hinges on the left hand side of the door". 

Comment by Hal Schmidt "Woodmeister" on December 21, 2010 at 9:19am

Al, you have a good eye,  Yes it was a design change because it was short on walnut and the length of the wood I had to work with.  I have the handles but did not install them because I do not think they would look right.  The 2 outer doors open from the middle, so 2 handles on the the left door and the middle door would be right next to each other.  I could leave the handle off the middle door or have no handles.  The handles I have are round and stainless.  Any thoughts?

Comment by Al Barale on December 20, 2010 at 8:20pm

That really looks good Hal.

Couple of questions Hal

Have you decided on what sort of handles your putting on the doors yet?

The rails and stiles on the middle cabinet door is different to the doors either side, was that a last minute design change?

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_