Comment
Jill,
Nice piece.
If you want to give the piece a different appeal, you could add some 1/8" long 1/4" dowels, in strategic locations. The dowel ends can be painted, a darker color, pressed/tapped in place, flush with the surrounding surface.
Yes Jay you are right with the difficulty of inset doors. You have to be very precise and square! I have done several different door panel styles and I think that insetting the doors shows the accuracy of the dimensions/cuts/construction to someone that knows how exact the measurements need to be! I do usually fill my pocket holes or hide them, because most of the pieces that I make are a little more formal, but I wanted this to look a little more like an older piece, something that could have been handed down. I am very happy with the way it turn out, build and finish. Thank you for your kind words!! I'll have to wait for Christmas next year for the Foreman : (((
Hi Jill, Excellent example of building a cabinet. Great job on doing the inset doors and the wire panels make this a fine example of a "One of a Kind" cabinet. Inset doors are the most difficult for any build as the fittings must be precise. It is nice to see something that is different instead of the same repeated styles that seems to be the normal anymore.
To be honest with you there is nothing wrong with showing the pocket holes as that is part of the build and showing the method of joinery is always good to see. The pocket hole method of building a door is strong and does show that there are other methods of building a door. It shows others who do not have all the cabinet door bits, that a pocket hole and screw is again a different method that works.
In building anything it is sometimes an advantage to use something different to set it apart from others and it becomes part of the character of the piece. I often will take a defect and if it can not be fixed so that it is not noticed then I will take the defect and turn it into something that is very noticeable. That makes the defect look as if it was done intentionally and becomes something that sets that build apart from all others. If you plug the pocket holes it is not always easy to completely conceal them so leaving them fully exposed makes it appear as being a normal way of building a door.
Nice job on the skirting of the cabinet bottom. Be proud of your project as it is very good.
Yes the Kreg Foreman is a good tool especially when you are building such projects I know you will enjoy the ownership of one. Thanks for sharing and keep on doing the inspirational work.
Not shameful very helpful thank you for the picture!!!
@Bullet - lining up the wire was pretty easy, I just followed the grids, pulling it tight was another story! I used my pneumatic stapler with 1/2" staples to attached it about 1 1/2 to 2" in. I am so embarrassed that my pocket holes were not filled in on this project!! I hid all the other pocket holes, all 120 of them, but I got lazy in the end! Shameful!
Jill, do you have any pictures of the back side of the doors? Great looking Cabinet, my OCD really likes how you kept the wire mesh lines straight in the doors LOL.
Nice job Jill ,keep Makin shavings .
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
You need to be a member of Kreg Owners' Community to add comments!
Join Kreg Owners' Community