mobile work bench
Do-it-all Mobile Work Bench
The original plans are from the Dec/Jan 2005 issue of The Family Handyman Magazine. I increased the length to fit the area in my garage and increased the size of both end shelves and one of the side shelves. The shelves are sized for my table saw and miter saw with my router attached to the router top. You can remove the router top and use the plain shelf (per plan) on that end if needed. Due to the length of the project, added extra supports under the top and shelves (using the Kreg Jig as much as possible). The top & shelves have 3 coats of MinWax Stain/Polyurethane. The last step was adding 20 amp outlets on all sides to power the saws, etc.
With all four of the side shelves up, you have a work surface of 57"x 127". Bench top is 26"x 84"x 37" high. The router table top & accessories are from Rockler. The locking casters are from Woodcraft. The John Sterling brand shelf brackets and hardware was ordered from HardwareWorld.com. All lumber, screws, electrical components, etc. was obtained locally at Lowe’s.
I can provide specific part numbers, cut sizes, more photos, etc. if interested
Comment
-
Comment by Bob Naylor on May 22, 2013 at 4:12pm
-
Thanks. Off to Lowes tomorrow.
-
Comment by Homer Moyers Jr on May 22, 2013 at 7:59am
-
On the way.
-
-
I would like a set of plans also. Thanks. rnaylor2@cox.net.
-
-
Sure, need your email
-
-
Can I get a copy of those plans too? Can't find them on the website either. Looks like a pretty cool workbench for my needs.
-
-
On the way to you.
-
-
That would be great - harp5610@msn.com - This looks like what I need for my small shop!
Thank you
-
-
I have the plans as a .pdf that I saved from the magazine a few years ago; can email to you.
-
-
Would I be able to get the plans? Or where would I find them? I have tried the magazine and was not able to find it.
-
-
Neat work. Hats off to you.
Need Help?
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
Popular Posts & Projects
Videos
Forum
Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
40mm Cup Hinge Jig Question
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
Product Reviews
New Kreg 720Pro
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Not Pleased With Pocket Hole Construction
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep.
Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service
You need to be a member of Kreg Owners' Community to add comments!
Join Kreg Owners' Community