Kreg Owners' Community

What works best at making nice crisp 90 degree edges on lumber that are exposed???

Views: 1854

Reply to This

Replies to This Discussion

Bill,

I use a router to dress the edges.

Much easier and get great results.

Hi Bill,  In reality there is the method where you can get a 90 degree angle to two planes of a piece of lumber by using a table saw of which, if it is accurate,you can cut the edge 90 degree to the flat side of lumber providing that the lumber side you lay on the table saw is totally flat.  The better way to obtain the 90 degree angle is to use a jointer to cutting the edge square to the face.  The best way is to pass the lumber through a thickness planner and then use the jointer to make the edge 90 degrees to the face that you just milled on the planner.

Jay is absolutely right about the table saw and a straight 90 degree edge.  You can make a jig for  your table saw that will give you great results.  Bill is also correct, you could use a router too as a jointer. 

Thanks to all for your suggestions, I may try the router 1st since I got the Kreg Router Table Package. I'm basically concerned more with the 2-by lumber that have sort of rounded edges for my work bench project. Other than cutting and planing your own dimensional lumber, do any of the box stores carry straight cut lumber in 2x4, 2x6 without any milling? I've found 2x6x48 oak at Menards cut in this way, but a little high end for my project.

Bill,

2x lumber normally features a rounded edge.

The purpose for the rounded edge, is to facilitate handling---

reducing the likelyhood of splinters injuring the person handling the material.

When I've needed 2x4 stock with a squared edge, I've purchased wider stock,

ripped off the rounded edge,

then run it thru a router, using a straight bit.

Rip the rough material oversize, about a 1/16", allowing for removal of material when making

the finish pass with the router to dress the edge nice and square.

When setting up your router table fence, make a 1/16" offset, on the trailing fence.

( I use shim stock, behind the router table fence.  Rockler offers these shims in a kit, with various multiple thickness sizes---use singly or in multiple, to produce the desired size cuts).

It's best to make multiple thin cutting passes vs a single wide pass, when using a router.

Router bit choice(s);

1. Spiral bit

2. Straight bit with a slightly slanted cutting edge.

(a slanted cutting edge bit will produce a shearing action and result in a smoother finish).

(I use 2" long cutting bits, with 1/2" shank, for this type operation).

Don't use a 1/4" shank bit---it'll result in wobble and chatter marks on your work-piece).

A combi machine will do the job Planer /Thicknesser.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Recent Workbench Survey Legitimacy

Yesterday, I received an email wanting my opinion on Kreg adding high end workbenches to their product line and wanted to know before I clicked the link if this is a legitimate survey or some phishing scam. Here's the link I was provided (…Continue

Started by JOHN W. GOETZ in Other Kreg® Products Dec 10, 2021.

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11, 2021.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_