Kreg Owners' Community

I am making an 75" x 40" frame with 2X4s and want each corner square.  Now  if I was using nails I would place one in each joint then measure the diagnols and square it up before putting more nails in the joint.  The Kreg system will pull the joint tight.  So what is the best way to square this frame using the Kreg system to join the 2X4s at right angles?

Views: 8281

Reply to This

Replies to This Discussion


Larry this is the fast method that I would use, do the diagonals and hold it in position with temp diagonal braces until you finish your permanent screws or nails then remove.  put two fasterners in each end of the diaagonal braces to prevent it from racking while you apply the permanent fasteners.
Larry Mathews said:
Jay & Jens,  I have used the diagonal method before with one nail in each corner until I got it square. In that case as long as it is not finish work if my cut was off a 16th it did not matter.  With using the pocket holes it seems to me the screws will pull it back out of alignment if the cuts are not dead on.  John's suggestion of using shims might solve that problem.  What do you think?  Of course as we all know the real answer is square cuts.
Good old Pythagorean useful tools to prove 90 degree angle.

I always use the 3-4-5 for large squares,   at 75x40.  If you measure 52" on the 75" side,  and 39" on the 40 " side.  the diagonal will be 65"  get it there and screw a 1 by to hold it in place... hope this helps  I used this to square 40 feet long with a 100' tape..  math is your friend   good luck

 

the same way as if your nailing should work.I use a jig for corners,but that is set up for 1x4x48 stock.You could always use a large square on your work and clamp it in place.My take on square corners is have your work cut straight and you will get good corners 99.99% of the time.

Pythagorean Theorem for all right triangles a2 + b2 = c2   

In our example a= 3 or 9 b=4 or 16    9 + 16 = 25 square root of 25 is 5 or c=5. For the 3-4-5 triangle will be a  90 degree 60 degree 30 degree right triangle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I

I'm in no way trying to argue, but a 3-4-5 triangle is not 30-60-90 degrees. 

 

It's more like 36.9-53.1-90 degrees. 

 

You can figure it out with a trig table.

I stand corrected you are right.  I checked out my memory is wrong. I'm now trying to remember the significnce of the 30 60 90 right triangle.
make a jig for your saw, and use a framing square in the corners also use the 3' 4' 5' rule . measure one peice 3' the adjoining peice 4' and the diagonal between the two peices will measure 5'. if it doesnt then adjust your wood until it does.
The 30, 60 & 90 angles, are one of the drafting/drawing triangle tools.

Gary roofner said:
.......................I'm now trying to remember the significnce of the 30 60 90 right triangle.
Have a table saw accident, win millions and have someone else worry about it LOL. sry couldnt help myself

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone Jul 22.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_