Kreg Owners' Community

I've been using track saw systems for many years. I had Eurekazone system for probably 15 years and just this past year switched over to a cordless Makita system. I got rid of my EZ cutting bench and replaced it with a MPC. Liked it so much I bought a second.

Today to break down sheet goods I use a newer product from Eurekazone called pyramid (believe they are available on Amazon). You can thread an included 3/4" peg in the bottom that fits perfectly into the MPC and the top has slots to accept 1x lumber. So I for a full ply sheet I make four assemblies which include: a length of 1x4 and two pyramids. Put these on my MPC's and life is EZ rip cutting the ply.

For crosscuts this pyramid solution is a little cumbersome since the ply pieces are smaller and it's more difficult to support them. I'm thinking some kind of cutting board would work best for this. Something like the MFT where you make a kerf cut into the top but I wouldn't need dog holes in it.

Was thinking I could:

1) just temporarily put 3/4" ply or MDF on the MPC tops 

2) could make the table bridge with 2x4's and lay a cutting board on it

Wondering if someone has already done this so I don't re-invent the wheel.



Views: 278


Reply to This

Replies to This Discussion

I have always used a piece of foam board insulation. It's light and will last quite a long time if you're somewhat careful on the depth of your cuts. 

You should be able to find it Home Depot or any other similar store. 

I've used foam board quite often but it's hard to use a saw track with clampsthat attach underneath.

Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 


  • Add Videos
  • View All


New to K5 and pocket holes, any video’s on the materials listed below?

I am using Danny Proulx book on shop workstations. I am deciding whether to use MDF or Melamine. He calls for MDF. However; I like the looks of the melamine.  I am a little leery of using pocket holes for it. One of the main reasons is I have no…Continue

Started by Michael Lusk in Beginners' Zone May 24.

Adaptive Cutting System T-Track Stops Mod 1 Reply

I bought the ACS a couple of weeks ago & have been pleased with the results on my first small project (LP record crates)... I was disappointed with the plastic accessories for the table-top, especially the T-Track stops. I'm pretty sure they…Continue

Started by John Moore in Beginners' Zone. Last reply by Deac Manross May 17.

Product Reviews

K5 Review

I really like the k5 it is faster to change from different size of screws. I hesitated to update because of some of the reviews about the dust collection hook up. That to me one of the improvements it works perfect no dust to cleanup .…


Posted by Gary roofner on April 5, 2019 at 10:02am

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…


Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…


Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service