Kreg Owners' Community

Hi Guys,

I just built my first project with the Kreg it was the Kreg Jig® Storage Unit.

I followed the plans and it came out perfectly I had no drama's at all.

BUT I have bought the Kreg master system 4 and some of the components are too big to fit into the draw so I cannot use it as an all in one storgae system this plan must have been made for earlier models.

I am not going to bother redrawing the plans, but all it would take is for the draw and obviously the housing to be another 1/2 inch taller to take all the accessories.

So I am sending out a warning for the next newbie to measure the tools that they want to hold and adjust the measurements to suit and then PLEASE PUBLISH THEM.


Cheers

Tom


Views: 825

Reply to This

Replies to This Discussion

That's interesting news! I just bought some baltic birch and was about to cut it according to the Kreg plans. Is that what you'd recommend, only making the drawer 1/2 in higher? Do you think any other dimensions need changing? Thanks

Hi Bill,

If you make it 1/2 an inch higher it will take all the accessories that come with the kit. You will have to make one of the draw compartments a bit larger than 3 inches to take the mobile base. Its best to just put your tools in it when finished and then place the dividers where they suit you best. It is not large enough to take the parts and boxes of screws as well, if you want to do that then you will have to make the entire project 3 inches wider.

The only other change is that I glues 2 1 inch blocks on the top so that I have a much greater resting area when drilling larger sheets see that attached photo

Cheers

Tom

Bill Lanterman said:

That's interesting news! I just bought some baltic birch and was about to cut it according to the Kreg plans. Is that what you'd recommend, only making the drawer 1/2 in higher? Do you think any other dimensions need changing? Thanks

Thanks Tom. Your storage unit looks great. I'll take your advice and add the extra 1/2" so I can get everything in. Much appreciated.

B/

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_