Kreg Owners' Community

Hi All

I am in the middle of finishing up a entertainment unit for the house and have one quick question. How is everyone staining once the project is built. The main unit is easy just sits on its feet and i can do the whole thing but the removable shelves present a problem. How do i stain and clear coat them all sides at once. Can this be done? I imagine if I do one side at a time let dry and do the other side you will see transition lines in the stain. What setup do you use for staining or painting all in one go?

Thanks

Views: 977

Reply to This

Replies to This Discussion

Why buy all these fancy setup tools. My gosh you must have 4 blocks of wood (1x4 or 1x2)  in house or shop.Just take some finish nails an pound the all way through the wood in corners turn upside and there is your system. $.25 vs.$10.00 or more .Thats all  I have to offer.

James set up is fine if you have space to store the board which I do have the room but with 1x4 I have 12 of them in a cabinet and takes up no room at all

I prefer James' solution with the painters pyramids. The plastic is less likely to mar your workpiece... and really, it's only $10. Your nails may be at different heights, etc... I don't know, I just prefer the accuracy of the pyramids. Either way will work. Kreg's bench dogs also have a 'painters point' on them:  http://www.kregtool.com/Bench-Dogs-Prodview.html

Now that just  dont make since at  all different heights.If you set the nail all way through board and then turn over

how can they be different heights.As far as marring these nails have a lot less space then your so called plastic. But each to there own I prefer to be conservative when settling for this type of tool.



Thanks for all of the great ideas guys. I have actualy made painters pyramids from 1/8 baltic birch cut out on the scroll saw so maybe I will just whip up a few more and see how that goes.

Thanks again.

Good for you as far as making your own

I have 2 sets of painter pyramids but I often find out that that is way less than I need, sometimes you need more then 8 supports. I take 1/4'' plywood scraps cut in aprox. 2'' squares and run a screw 3/4'' long through the center from the under sides.

you can make a whole lot of these fo the price of the pyramids but the pyramids take up alot less space when being stored

 

How do i stain and clear coat them all sides at once. ... I imagine if I do one side at a time let dry and do the other side you will see transition lines in the stain.

No, you won't see transition lines. it's easy to stain just the top and the sides, let it dry, then flip it and stain the remaining side.

If you doubt your dexterity, try this:

  1. Mask the edges of one side with painter's tape.
  2. Prop them up on something - those pyramids, the nails or whatever works so that you can reach all the edges.
  3. Stain the top and the 2 edges that will be visible (assuming sides will always be hidden). Be careful to not swab the underside carelessly and go past the tape.
  4. Remove tape and let it dry.
  5. Mask the visible edges
  6. Flip the shelf over and stain the remaining side. remove tape and let it dry
  7. Do one side and all edges with the clear coat, let dry and then do the other.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Popular Posts & Projects 

Videos

  • Add Videos
  • View All

Forum

First time I really had a need for the ACS miter guide.

I've been using my Adaptive Cutting System table for a few years now, and it's been really solid. This past week was the first time I ever needed to use the miter guide though.I was rebuilding some shelving in a tiny closet and I discovered the…Continue

Tags: ACS

Started by Adam in General Woodworking May 6.

What thread and size screw to use 2 Replies

I am building a small trunk for a military friend to put some belongings in. I have made legs out of ash hardwood and will make the sides out of 1/2” or 3/4” Baltic birch plywood. The legs are 1.5” thick by 2” wide. So since I’m drilling pockets in…Continue

Started by Mike Bohannon in Beginners' Zone. Last reply by Jay Boutwell Apr 19.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_