"The problem with traditional squares is that while they give you a straight edge, they do nothing to simplify and speed up the process of aligning your saw to your pencil mark. The Kreg Square-Cut™ simplifies this
process with an adjustable guide arm that can be set to work with any circular
saw or jigsaw. Simply match the arm to your saw’s unique offset, then use the
Square-Cut™ to make fast and accurate cuts over and over again.
The Square-Cut's adjustable guide arm can be set to match any circular saw or jig saw. It compensates for the length from the blade to the edge of the base plate. What does this mean for you? Instead of eye-balling
the blade on the pencil mark or using your tape measure to set back your saw
from the line to a specific length, all you have to do to get a perfect cut is
place the guide arm next to your mark, and make your cut. Faster results, fewer
mistakes, and much less aggravation."
Tags:
I recently purchased the Square Cut tool; & had my first chance to use it today.
I calibrated it on a Skil circular saw. The Square Cut tool is an absolute blessing!
I followed the directions to the letter. And I got perfectly squared cuts time after time,
right on the money!
Once you have the tool squared for your particular saw, it even allows for the kerf.
All my cuts measured exactly the way I measured them before cutting. That tool will
get constant use from now on, with every project when I have to cut boards!
It's a great tool, but the statement any circular saw does not take in the battery saws, I have a ryboi 18volt that I use more than the larger skil saw. And the guide will not go in far enough, I'm sure there are a lot of people that use the battery saws because you don't have to deal with the cords. After sending in an inqurie has to this and got no where I made one out of hard wood that works (thats just the slide out only, not changing and thing with the main part). Thank You the tools are great. Garry CharlandGarry, I totally agree with you on the part about "any circular saw". All the saws are notcompatible with this tool. I happen to have the dual saw, which is a great tool. But to makethat dual saw into a standard type circular saw, I would have to buy a seventy dollar attachmentto make it work as a circular saw.But, I am not ready to do that. My old Skil saw works just great with the Square Cut tool.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service