Kreg Owners' Community

What SHOULD be my next piece of equipment   ?   I have : Table saw, circular saw, router, miter saw, various drills and drivers,palm sander,angle grinder, jigsaw, Kreg kit and a few clamps.  My space is limited and so is my time as I still work a many as 50 hours at 56 years of age and still love what i do so no slowing down for me yet.  

   

I was thinking maybe a combination sander 4inch belt 6inch wheel type?  Bench top drill press? Going to build another heavier bench soon to use for heavier equipment operations'

Views: 1152

Reply to This

Replies to This Discussion


My router can go either way.  I still may purchase a fixed base router to dedicate to the table.  I also have a insert for the router base that I believe is used for patterning.  
Ken Darga said:

A router, with a fixed base, can be used for hand-held routing operations.

Depth adjustments are accomplished by the adjusting feature, that is intergral with the router base.

Just now noticed your reply.  I tend to agree.  I would prefer to have a dedicated router for the table.

I am planning on adding a router table if the weather ever warms up enough in these parts to get me going.  I am looking at the Bosch.  I would like to mount it to a mobile work station as a designated work area just for routing.   I could be wrong Rick but I think you would want to mount a fixed router to the table.   A plunge router for free hand work.  My router now is both fixed and plunge but plan on a separate heavier motor for the table.   All in good time :)

A P-C 893 router, for example, includes two bases---

a fixed base and a plunge  base.

The fixed base can be mounted in the router table and the plunge base can be used for hand-held routing operations.

It's a simple task, to open the locking mechanism, and move the router from the plunge base to the fixed base, 

and visa versa.  This permits one to have a single router for both uses.

There are various router OEM's, that offer such features.

Currently Rockler is offering a P-C 895K router kit, for $260 (reg price $290)---

and includes a $42 brass bushing kit FREE.

I think since I have a plunge router that seems to be adequate i will save a few bucks and buy a fixed base.  That way I can get a bit more quality for my money but less features.  I would dedicate it to a table.

If you are looking for a fixed base to match your plunge, I'd say keep an eye out on Ebay.

Rick said:

I think since I have a plunge router that seems to be adequate i will save a few bucks and buy a fixed base.  That way I can get a bit more quality for my money but less features.  I would dedicate it to a table.

  • Same general specs 1.75 HP  1/2 and 1/4 inch chucks,  Fixed Base,  Milwaukee or Porter Cable.   Thoughts  anyone? 

Rick,

My choice is the P-C.

P-C has been the workhorse in routers.
P-C routers have been around a long time, and have been the industry standard,
from which other routers are based.

P-C offers the largest readily available accessories.

Something to consider, for expanding your router accessories & options.

Limited accessories available for other routers, on todays market.

I've had a P-C 690, single-speed 1.75HP, fixed base hand-held router for many years.
To date, it's performed flawlessly.

An optional plunge base is available for the 690, if you chose to purchase one, at later date.

I also have the P-C 890VS (variable speed) series, the 2-3/4HP model.

NOTE: A slower speed is needed when spinning larger bits.

 Heheheehee, these conversations generally degenerate into a "which is best; red Ford, Blue Chevy or Green Dodge..... "  In this case, I have to respectfully disagree with Kens assessment of the Porter Cable product line. Black and Decker bought the P-C flag a couple of years ago and have been "repositioning" the brand in the market place. I doubt seriously that the Porter Cable of today is the same robust machine your father was able to buy 20 or so years ago. Moreover, B&D has not seen fit to upgrade much of the line, the exception being the introduction of the 450 PK, a small, 1 HP trim router with a plunge base. The prices have also stayed relatively high which, IMHO, reduces their value/$. IMO, a much better value would be the Bosch 1617 , which is a 2-1/4 HP router at least the equivalent of the 893 for roughly $100 less money. As far as pure value/$ the new line of Craftsman routers, $100 - 150 range are very hard to beat. As far as accessories go, since the P-C has been around a long time, most other router mfg have adapted their routers to accommodate most P-C compatible accessories and, in some cases improve on their use.

There are many good routers on the market. I believe the best approach is to handle as many variations as possible to find the one with the best ergonomic fit for you personally. Pay attention to the controls; plunge release, power switch location, bit height adjustment.. etc and choose the one that feels more natural to you. I have several routers of different brands and each does one type of job a little better than another.

I purchased the Milwaukee.  I have several of their tools and feel good with the brand.  The model I choose is also compatible with the bosch cabinet bench top router table I am looking at.

Congratulations, Milwaukee are great tools. I'd love to put their 5625 router in my table but the old Freud hasn't given me an excuse to. :)
 
Rick said:

I purchased the Milwaukee.  I have several of their tools and feel good with the brand.  The model I choose is also compatible with the bosch cabinet bench top router table I am looking at.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Pantry slides for heavy application

  Recently purchased two 96" tall pantry cabinets that are 23" deep that only came with two adjustable shelves and two fixed, (one at about 55" and one at the very bottom).  Shelf holes in the walls are drilled 2" O.C.  Like most store-bought…Continue

Tags: drawer, slides, pantry, pull-out, 75-Lb

Started by Paul Coon in General Woodworking Aug 11.

Miter Saw Recommendation 1 Reply

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone. Last reply by Scott Davison Oct 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_