Kreg Owners' Community

 

 

Introducing the Kreg Rip-Cut™


Available at Kreg Dealers everywhere

$34.99


Ripping down large panels into smaller more manageable workpieces can be one of the trickiest, most intimidating, and expensive steps of any wood project. Even for experienced woodworkers ripping with the nicest table saws, you’re still forced to lift large heavy panels, balance them carefully to avoid binding and bowing, while at the same time trying to support the finished workpieces  and waste material as they exit the saw.

 

There is a faster way. There is an easier way! There is a better way.

Introducing the Kreg Rip-Cut™.

 

The Rip-Cut™ is an incredibly handy tool which speeds and simplifies the process of ripping down large plywood and MDF panels. No more taking your work to the saw, instead take the saw to your work. No measuring, no marking, no chalk lines – the Rip-Cut™ quickly and easily attaches to almost any circular saw, letting you cut pieces up to 24” wide with tremendous accuracy.

 

The Rip-Cut™ is a no-nonsense, straight forward, precision accessory for your circular saw that is so incredibly affordable it will pay for itself in no-time. It features a durable design including a solid aluminum guide rail, ultra-durable impact resistant plastic, an easy-to-read precision adjustable scale, and a reversible guide arm which works whether you’re left or right handed. It’s a super easy, precise, and affordable way to break down large panels for almost any project.

 

  • Connects to almost any circular saw – right or left blade
  • Reversible Guide Arm for Right or Left Hand Use
  • Makes rip cuts up to 24” wide
  • Rip sheets of plywood in half – in just one cut
  • No measuring, marking, and no chalk lines
  • 100% Guide support through entire cut
  • No need to remove Rip-Cut™ when doing cross cuts
  • Quick and accurate adjustments – no tools required
  • Lightweight/Sturdy Design for use on the jobsite

 

Materials:
High Quality Aircraft Aluminum
Impact Resistant Plastic Polymer

Aluminum Guide Rail:
3" wide x 30" long
 

Saw Sled

6 1/2" x 8 1/2" saw platform

Guide Arm:
2" wide x 10" long
Minimum 5" edge bearing at blade entry
Minimum 3" edge bearing at blade exit
 
Cut Width:
Maximum 24"

 

Check out the Rip-Cut on www.kregtool.com!

http://www.kregtool.com/RipCut-Prodview.html

 

 

 

 

 

Views: 49901

Reply to This

Replies to This Discussion

1/2 length wise so you can have 24x96 panels. It's designed for rip cutting plywood not cross cutting. It's competeing for the 8 foot saw guides people buy.

Ronny Roach said:

I can't see how you can cut a 4x8 sheet in half in order to have two 4x4 

Looks interesting.

I suppose if you dont have a table saw then perhaps this is an option for some cuts, but this may be an answer to a non-existing problem.

Looks like a must have for me!

This assumes that the end of the 4X8 is square?

If I am ripping numerous fir strips, then I don't want to waste my time setting up a track guide for every cut. 

This tool then would be perfect, since the rip guide that came with my Makita is a piece of junk.  I don't see this so much as a cabinet maker's tool, but a contractor tool. 

I don't like using the edge of the wood as my straightline guide and the 24" max cut is not useful enough.

It does say on the page and in the small video that it will make cuts from 1/8" to 24" and that it will rip sheets of plywood in half, not crosscut them in half.

Ronny Roach said:

I can't see how you can cut a 4x8 sheet in half in order to have two 4x4 

I would love to replace my table saw with something simple like this or others but my main issue is if the board is not straight from the beginning, then it is a no go.  Is that true?  Den made this point.

Den said:

Guess it's OK if the cost is under 20 bucks. It seems okay if the matieral has a straight edge to start with.

I might as well pay the guy at the home depot .50 cents a cut to make a 4x8 sheet smaller. I've had good luck with my T-square to make straight cuts.

I see the value in either final cutting or ripping the same width ply multiple times. I'll still need my track to rip down large sheets but I could make the final cut with this if its completely accurate.

It is very misleading. You can only cut it in haft 2x8 not 4x4

Ronny Roach said:

I can't see how you can cut a 4x8 sheet in half in order to have two 4x4 

Should we all go back to Carpentry 101? a rip is cutting the material long ways. this is a "rip-cut". Everyone wants it to cut 48 inches, I personally can not reach 48 inches to verify that the edge of the jig is staying flush with the end of the board. For that i will use my handy dandy 1x4 and 2 Kreg Clamps. For taking off 12 or 18 inches off a sheet of plywood this would be awesome. I have a table saw but once again i am not big enough to hold a 3/4" sheet of ply steady to make a safe cut. I can tell you this much its an easy sell to my wife so she will have the piece of mind that i am being safe looks like my next birthday or christmas present.  keep it up Kreg another item on my tool bench.

I agree with most of the comments being made. I expected something truly innovative from Kreg. As I love and have most of their jigs and fixtures. I must admit that I am a bit disappointed at this latest offering. I too will stick to my hardboard and plywood "homemade" saw guides. They give me a very consitent cut. $35 for another "gimick" is a bit exorbitant. Without seeing an actual "in use" video, i would think that this fixture would want to wander. I could see myself trying to push the saw thru the cut while fighting to keep the fixture secure against the edge of the plywood with my other hand. This sounds like a real pain. Just my $0.02 worth.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Miter Saw Recommendation

I’m looking to upgrade my miter saw. I’m willing to invest a good amount of money to get one with the precision pocket hole joinery requires. Would anyone like to offer a recommended model?

Started by Joe Racz in Beginners' Zone Jul 22.

Miter saw stand

     Has anyone used one of the Kreg Universal Stand configurations as the base for a miter saw workstation with fold down wings?  I scrolled through the pics in the community and all I saw were using a DIY base cabinet.  I have an extra Kreg router…Continue

Tags: saw, Miter

Started by Bill Murphy in Other Kreg® Products Jun 6.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 8 Comments

© 2021   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_