Kreg Owners' Community



Introducing the Kreg Rip-Cut™

Available at Kreg Dealers everywhere


Ripping down large panels into smaller more manageable workpieces can be one of the trickiest, most intimidating, and expensive steps of any wood project. Even for experienced woodworkers ripping with the nicest table saws, you’re still forced to lift large heavy panels, balance them carefully to avoid binding and bowing, while at the same time trying to support the finished workpieces  and waste material as they exit the saw.


There is a faster way. There is an easier way! There is a better way.

Introducing the Kreg Rip-Cut™.


The Rip-Cut™ is an incredibly handy tool which speeds and simplifies the process of ripping down large plywood and MDF panels. No more taking your work to the saw, instead take the saw to your work. No measuring, no marking, no chalk lines – the Rip-Cut™ quickly and easily attaches to almost any circular saw, letting you cut pieces up to 24” wide with tremendous accuracy.


The Rip-Cut™ is a no-nonsense, straight forward, precision accessory for your circular saw that is so incredibly affordable it will pay for itself in no-time. It features a durable design including a solid aluminum guide rail, ultra-durable impact resistant plastic, an easy-to-read precision adjustable scale, and a reversible guide arm which works whether you’re left or right handed. It’s a super easy, precise, and affordable way to break down large panels for almost any project.


  • Connects to almost any circular saw – right or left blade
  • Reversible Guide Arm for Right or Left Hand Use
  • Makes rip cuts up to 24” wide
  • Rip sheets of plywood in half – in just one cut
  • No measuring, marking, and no chalk lines
  • 100% Guide support through entire cut
  • No need to remove Rip-Cut™ when doing cross cuts
  • Quick and accurate adjustments – no tools required
  • Lightweight/Sturdy Design for use on the jobsite


High Quality Aircraft Aluminum
Impact Resistant Plastic Polymer

Aluminum Guide Rail:
3" wide x 30" long

Saw Sled

6 1/2" x 8 1/2" saw platform

Guide Arm:
2" wide x 10" long
Minimum 5" edge bearing at blade entry
Minimum 3" edge bearing at blade exit
Cut Width:
Maximum 24"


Check out the Rip-Cut on!






Views: 50527

Reply to This

Replies to This Discussion

I ordered the rip cut from peachtree woodworking, and should be recieving it this week, so anxious to show it off to my co workers, i think when they see it at work, they will want to order one also, i think it's awesome !!!

Magazine editors, bloggers, etc. Contacts who have an 'audience' who can share our tools with the DIY/woodworking world. ;)

Jens Jensen said:

You mentioned that only media contacts have the guides,.What is a media contact

Does anyone know when in April this will be released?

I ordered mine yesterday from Factory Authorized Outlet/Kreg with free shipping for orders $25 and over. Scheduled to be shipped on April 12th so I hope that holds true as I'm anxious to try this item.

Exactly my question also. Have you gotten a responce from Kreg? I'm a big Kreg fan (user). I like the concept but starting could be a problem. Hope they give a response.
Kamil Czuba said:

Is there a video of actual use?  All the pictures show the saw half way through the panel.  I'd like to see one at the start of the panel, as only 1-2" of the guide piece will be touching the side of the panel.  Not very stable.

I was told that it would be in the second week of April...

I received and email on Thursday the 5th saying my order was shipped via FEDEX, so I should receive it early this week. Will post when it arrives.

This  would have been awesome to have for the bathroom remodel I just did!Must have for the next project. 

My rip cut jig arrived today. I was a bit concerned with the videos as they all showed this using a 7 1/4 " electric saw and that's something I almost never use anymore since I got the cordless 5 1/2" a while back. I was glad to find I can use the smaller one on this. Both assembly and calibration was easy. I don't have anything large to work with at this time so made a few one inch cuts on a small piece of scrap and they were all dead on. This is obviously made for larger pieces as it would be impossible to work around clamps because the guide rail hits them. I laid a couple router pads on the sawhorses for practice pieces to keep from shifting. Starting the cut seemed easier than finishing but maybe that's just me and will improve with practice. Once you have this jig set up for the saw you will be using taking it off an putting back on is a breeze. I may partially drill a couple holes in the saw base where the points of the two set screws go. I don't know why they have these so pointed. This is in no way a complete review as i just messed with it for about an hour.....but it seems to be something I may use when the need arises. Although I have a pretty good set up with the straight edge now. Just another addition to the shop that may or may not be used all that much but is there if needed.

I forgot to mention one thing in my post on receiving the Rip-Cut jig today. It was a welcome surprise to see this was "Made in the USA"!  We see that far too seldom with tools now a days.

hi just writing to whom it may have a answer to the? WONDERING WHY WHEN I CONTACT WOOD CRAFT  on line

ordering for the new rip cut they charge more then  kreg site for the same thing what i saw was 34.99 and for shelf pin was 34.99 and when i go to wood craft they were willing to sell me same thing for 36.41 for rip cut and another 36.41 for shelf pin jig wow am canadien  not dumb so why do they try to jack up prices like that when our dollar is worth as much i ordered other stuff from the usa on line and they dont charge more to canadiens then  what is said that was the price plus shipping and handling besides taxes and border free so what cost 69.98 for me would cost more like over 112. to get the same thing why jack up prices like that not fair to deal with these people that try to take advantage gee can anyone from kreg  has a reply would like to know if possible please and why do canadien on line  like lee valleys dont have new  items above yet thank you or busy bee tools


Reply to Discussion


Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 


  • Add Videos
  • View All


First time I really had a need for the ACS miter guide.

I've been using my Adaptive Cutting System table for a few years now, and it's been really solid. This past week was the first time I ever needed to use the miter guide though.I was rebuilding some shelving in a tiny closet and I discovered the…Continue

Tags: ACS

Started by Adam in General Woodworking May 6.

What thread and size screw to use 2 Replies

I am building a small trunk for a military friend to put some belongings in. I have made legs out of ash hardwood and will make the sides out of 1/2” or 3/4” Baltic birch plywood. The legs are 1.5” thick by 2” wide. So since I’m drilling pockets in…Continue

Started by Mike Bohannon in Beginners' Zone. Last reply by Jay Boutwell Apr 19.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…


Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…


Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2022   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service